全17件 (17件中 1-17件目)
1
チューナーを使って調弦するのは簡単です。ウクレレののすぐ近くにチューナーを置いて、1弦を弾いて画像のようにまっすぐになり上の黄緑色のランプが点灯したらOKです。左に振れたら低く、右に振れたら高いので弦の張り具合を変えて調弦していきます。チューナーで調弦 posted by (C)革人形の夢工房
2010.10.15
コメント(0)
このチューナーを近くの楽器店で買ってきました。絶対音感とは無縁の耳ですので、これでかなり調弦が正確に出来るのではないかと・・思っています。チューナー posted by (C)革人形の夢工房【宅配便専用】【クロマチックチューナー CA-1】【宅配便専用】【定番】【クロマチックチュー...価格:1,470円(税込、送料別)
2010.10.14
コメント(0)
ラッカーを塗ったウクレレに付属の弦を張りました。調弦はギターとは違うのでネットで調べて合わせてみようと思います。弦を張る posted by (C)革人形の夢工房
2010.10.13
コメント(2)
ウクレレにラッカーを筆塗りしました。乾いてから好みの光沢になるまで塗ります。ラッカー塗装 posted by (C)革人形の夢工房
2010.10.12
コメント(0)
サンドペーパーをかけたウクレレに水性着色剤のオークを筆塗りしました。乾いたら好みの色になるまで重ね塗りします。塗装 posted by (C)革人形の夢工房
2010.10.11
コメント(0)
塗装の乗りが悪かったので再びサンドペーパーで塗装膜を削り落しました。このあともう一度塗装します。塗装膜落とす posted by (C)革人形の夢工房
2010.10.10
コメント(0)
ウクレレを再塗装して、ラッカーの被膜がどのくらい落ちたか確かめてみました。前回よりは色の乗りは良くなりましたが、まだ残っていますのでもう一度サンドペーパーをかけることにしました。再塗装 posted by (C)革人形の夢工房
2010.10.09
コメント(0)
指板のはみ出している接着剤跡にサンドペーパーをかけてから、再塗装してみましたがまだフレットの際に白い線が残ってました。本体もこれから再塗装してペーパーがけの具合を確かめます。全体にペーパーがけ posted by (C)革人形の夢工房
2010.10.08
コメント(0)
指板にはみ出していた接着剤を落とすためにサンドペーパーをかけました。ウクレレ本体にも同じようにサンドペーパーをかけていきます。指板修正 posted by (C)革人形の夢工房
2010.10.07
コメント(0)
ウクレレに塗ってある塗装膜をサンドペーパーで削り落していきます。指板にはみ出ている接着剤がかなり強力なのでなかなか落ちてくれません。塗装膜を落とす posted by (C)革人形の夢工房
2010.10.06
コメント(0)
このウクレレキットには最初から無色のクリアラッカーサンディングが塗装してあるので木目を活かした仕上げが出来ません。そこで水性着色材を全体に塗ってからサンドペーパーでその色をすべて落としていきます。ネックの指板も着色してみたところ、フレットを指板に接着した時の接着剤と思われる部分が白く浮き出てきました。この白い部分を重点的にサンドペーパーで削っていきます。着色 posted by (C)革人形の夢工房
2010.10.05
コメント(0)
このウクレレキットは無色の塗装(説明書ではクリアラッカーサンディング)がしてあるので、このまま塗っても木目をいかした仕上げは出来そうにありません。そこで一応サンドペーパーを全体にかけてから着色してみようと思います。サンドペーパーがけ posted by (C)革人形の夢工房
2010.10.04
コメント(0)
三弦を取り付ける切り込みが二弦側に寄りすぎていたので、その部分を切り取って反対側に接着しました。ブリッジ修正 posted by (C)革人形の夢工房
2010.10.03
コメント(0)
丁寧に作られているキットなのですが、弦を留め付けるブリッジの切り込みが等間隔になっていません。この部分を等間隔になるように修正していきます。ブリッジ修正点 posted by (C)革人形の夢工房
2010.10.02
コメント(0)
ネックの指板接着部の細かい隙間などをパテで埋めていきます。3000円のキットにしては以外に丁寧に作られていると思います。すきま posted by (C)革人形の夢工房
2010.10.01
コメント(0)
このキットはほとんど出来ているので、糸巻きを付けて弦を張るだけで一応弾くことは出来ます。調弦はネット上のサイトでどうにか調整して弾けるようになりましたが、ギターとはまったくコードの指使いが違うのでまだほとんど弾けません。これからキットに仕上げのサンドペーパーをかけてから、色付けしてラッカーかニスで仕上げます。ウクレレキット組み立て posted by (C)革人形の夢工房全音ウクレレキット価格:6,300円(税込、送料別)こちらは本格的なキットです。
2010.09.30
コメント(2)
ヒョウタンでウクレレを作ってみようと思い立ったのですが、いきなりでは解らないことばかりなのでキットを一つ作ってみることにしました。楽器店で見つけたのは鈴木楽器製作所の「スズキキット教材 ウクレレキット」(税込3129円)です。このキットは塗装以外ほとんど出来ていて、付属の糸巻きと弦を張れば一応弾くことは出来るようです。こまかな部分は作り手の技術に合わせて仕上げられるようになっています。10.09.29 015 posted by (C)革人形の夢工房
2010.09.29
コメント(0)
全17件 (17件中 1-17件目)
1