1
SSMODEL製 3Dプリントキットアメリカ T1E6軽戦車 昨日(2024年9月20日)で組立作業2日目です。タミヤの水性アクリル塗料で塗装しました。全て筆塗りです。排気管や各転輪のゴム部の塗分けも終わっています。昨日の作業時間は1時間20分です。累計作業時間は3時間00分です。
September 21, 2024
閲覧総数 109
2
今朝は午前4時30分に起床です。昨夜から継続してエアコンの冷房を27度設定で稼働させていて、起床時の室内の温度・湿度は28.2度、45%、外気温は26.7度、天候は曇りです。起床時の血中酸素飽和濃度は97%、体温は36.5度でした。午前5時45分にGH3インプレッサで福山市内の住居を出発、国道二号線で福山西インターから山陽自動車道に入り、尾道自動車道、松江自動車道、国道54号線、国道9号線を走って自宅に戻りました。自宅の到着は午前9時05分です。福山市の住居を出発時に燃費計をリセットして、燃費は15.7km/Lです。国道9号線を走っている際の燃費は15.9km/Lだったのですが、以降、少し渋滞もあって、燃費が落ちました。本日は、定期の内科通院だったので、少し休憩してから、内科クリニックに行って、診察が終わって院外薬局で薬を購入してから、境港市内に行って用事をしてきました。昼ごはん丸合で買った「大山おこわ」を主食に、チルドシュウマイ、カボチャ煮、里芋と揚げのお味噌汁です。お味噌汁は、現在、愛媛では「いもたき」の季節なので、それに合わせた具材になっています。午後から、エディオン米子店などに行ってきました。ローソンで先週のジョブチューンで紹介されていたスイーツを買って食べました。カスタードプリン、確かに美味しいです。境港市のプラント5で売っているオリジナルの焼プリンも、これと同じくらい美味しいです。午後5時過ぎ、酸欠気味で頭痛がするので、ちょっと横になるつもりいた寝てしまい、気づいたら午後6時を過ぎていました。晩ごはん焼魚(赤魚の粕漬け、鯖の味醂漬け)と焼きピーマン、サラダ、お昼に同じく里芋と揚げのお味噌汁です。午後7時過ぎ、血中酸素飽和濃度を測定したら93%でした。
September 21, 2024
閲覧総数 98
3
朝ごはんハローズのちくわ(1包4本入り。約107Kcal、製造はマルハニチロ)、マリンフードのキャンディチーズ4個(1個約14kcal)、餅吉のおせんべい1枚(サラダ・57kcal)です。
September 21, 2024
閲覧総数 74
4
2024年 42個目のプラモ中国のSSMODEL製 3Dプリントキットアメリカ T1E6軽戦車 昨日(2024年9月19日)、組立開始です。T1E6軽戦車は、T1E1軽戦車の進化系で、1932年に製造されました。T1E1軽戦車は足回りがルノーFTと同じ形式でしたが、T1E4軽戦車からは、足回りがイギリスのヴィッカース 6トン戦車を参考にしたリーフスプリング・サスペンションを採用し、搭載されるV8エンジンも、フロント配置からリア配置になって、トランスミッション・フロントファイナルドライブ方式となりました。T1E6軽戦車は、T1E4軽戦車の装甲の増加その他の変更に対応してエンジンをV12にして出力向上させたものです。3Dプリントキットなので、例によって、サポート材の除去から始めます。部分的に硬化が不十分なところもあり、表面がべとべとしている部分もあったのでUVライトを照射してベトツキがなくしてから、作業しました。購入したキットは、届いた時からフロントフェンダーが割れていて部分的に変形して隙間が出来ていたので、サポート材を除去してから、その修正作業を行いました。パテ代わりにゼリー状瞬間接着剤を盛って、硬化促進剤で固めてから、超音波カッターで削ったり、キサゲたりして形を整えました。履帯と一体になっている誘導輪ですが、非常に繊細で、切り離してから、少し力がかかったら、砕けるように割れました。修正に時間を取られました。この状態で塗装作業に入ります。昨日の作業時間は1時間40分です。
September 20, 2024
閲覧総数 106
5
今朝は午前5時30分に起床です。エアコンを27度設定で稼働させて、床時の室内の温度・湿度は28.7度、49%、外気温は24.8度、天候は晴れです。起床時の体温は36.6度、血中酸素飽和濃度は96%でした。午前6時50分に運動のために歩きに出かけて、いつもの猫スポットまで往復してきました。猫スポットでは、黒猫1匹を確認しました。一見すると耳がカットされていないようですが、右耳にカットがある桜猫(地域猫)です。某マンションでは黒猫2匹を確認です。2匹とも、少しお話をしました。近所の三毛も遠くに確認できました。今朝も猫を見たから頑張ろうということで、いつもの時間よりも、10分早く出勤し、また、直ぐに仕事を始め、昨日のやり残しは午前8時10分には処理し終わり、その後、ルーティンのしょる処理であっという間に昼になりました。昼ごはんいつもの給食弁当です。メインのおかずは豚天です。昼休み時間定時で帰りたいので、仕事をしていました。午後から、精神的にも疲れてきましたが、何とかなると思います。ほぼ定時で帰って、住居に戻って血中酸素飽和濃度を測定したら94%でした。晩ごはんの焼そば麺は藤本食品の蒸し麺、具は大山ハムのポークウインナー、もやし、えのきだけ、キャベツ、ぶなしめじ、ニンジンです。赤天、ミニトマト、めだまやきを添えました。別添で鶏唐揚げ、イカ唐揚げがあります。
September 20, 2024
閲覧総数 98
6
今朝は午前5時30分に起床です。エアコンを27度設定で稼働させて、床時の室内の温度・湿度は28.9度、51%、外気温は26.3度、天候は曇りです。起床時の体温は36.5度、血中酸素飽和濃度は95%でした。午前6時50分に運動のために歩きに出かけて、いつもの猫スポットまで往復してきました。猫スポットでは、従来からの白キジを確認しましたが、高速で走って自動車の下に隠れてしまったので、さつえいできませんでした。某マンションでは黒猫2匹を確認です。いつもの時間よりも、20分早く出勤し、また、直ぐに仕事を始め、あっという間に昼になりました。昼ごはんいつもの給食弁当です。メインのおかずは鶏天です。本日のごはんは麦飯です。味付けとろろ芋が付いています。麦飯は大好きなので、嬉しいです。毎日が麦飯でも良いです。昼休み時間本日は、福山港は正午が満潮時間だったので、職場横の側溝にも水が上がってきて、カニも側溝の上の方まで来ていましたため、カニの詳細を見ることができました。ハサミの形状が異なっていたり、脚に毛が生えているカニと毛がないカニがいたので、やはり複数種のカニが同居しているようです。午後からも、事務処理が多く、眼がかなり疲れます。一部を明日の朝に持ち越すことにして、ほぼ定時で帰りました。住居に戻って血中酸素飽和濃度を測定したら97%でした。晩ごはんの焼そば麺は藤本食品の蒸し麺、具は牛豚合挽肉、もやし、えのきだけ、キャベツ、ニンジンです。赤天、ミニトマト、めだまやきを添えました。別添で厚揚げ、アジフライがあります。
September 19, 2024
閲覧総数 128
7
朝ごはんハローズのちくわ(1包4本入り。約107Kcal、製造はマルハニチロ)、マリンフードのキャンディチーズ4個(1個約14kcal)、餅吉のおせんべい1枚(しょうゆ・70kcal)です。
September 20, 2024
閲覧総数 80
8
2024年 41個目のプラモ中国のSSMODEL製 3Dプリントキットアメリカ T1E1軽戦車 昨日(2024年9月18日)、組立作業2日目で完成です。昨日は、ヘッドライトレンズの塗装他、塗装のダメ廻りを行いました。ヘッドライトはレンズ部をタミヤのエナメル塗料のクロームシルバーで塗ってからUVレジンのクリアーを上塗りしてUVライトを照射して固めておきました。昨日の作業時間は40分です。完成までの累計作業時間は3時間00分です。実車の諸元は、次のとおりです。全長 3.87 m全幅 1.79 m全高 2.18 m重量 7.5 t主砲 M1918 37 mm 短戦車砲副武装 M1919 7.62 mm 機銃(同軸)装甲 6.4-9.5 mmエンジン カニンガム 水冷V型8気筒ガソリン 110 hp乗員 2 名排気管も駆動輪・誘導輪等の複雑な形状も3Ⅾプリントキットなので、一体成型で精密に再現されています。M2A2軽戦車と並べてみました。
September 19, 2024
閲覧総数 123
9
タミヤ 1/35スケールミニタリーミニチュアシリーズ No.384ドイツ軍用サイドカー KS600昨日(2024年7月30日)で組立作業3日目です。 フィギュアを組み終わり、塗装中です。道標は、角材状の部品に、キットの上箱側面に印刷されたものを貼り付けるようになっています。サイドカーは、ナンバープレートとメーターのデカールを貼って、艶調整しておきました。昨日の作業時間は1時間40分です。累計作業時間は4時間00分です。
July 31, 2024
閲覧総数 242
10
MENGモデル製 1/35スケール ロシアT-90主力戦車、TBS-86ドーザーブレード搭載昨日(9月6日)で組立作業6日目です。赤外線サーチライトを光らせるLEDランプ用のボタン電池を買ってきたので、点灯テストをしてみました。ライトレンズ面にマスキングテープを貼った状態でも、ここまで明るく光ります。引き続き砲塔へ爆発反応装甲や各種センサーなどの部品を取り付け作業を行っています。部品が多くてクラクラしてしまいます。昨日の作業時間は、午後9時40分から午後11時20分までの1時間40分です。累計作業時間は11時間30分です。
September 7, 2016
閲覧総数 488
11
トランぺッター製 1/35スケール ブラジル陸軍 EE-T2 オソリオ 昨日(2021年10月4日)で組立作業4日目です。 車載工具や砲身のキャンバス部の塗分け、墨入れ、ペリスコープ等への透明部品の取付け、デカール貼りを行いました。 昨日の作業時間は50分です。 累計作業時間は5時間30分です。
October 5, 2021
閲覧総数 327
12
2024年 41個目のプラモ中国のSSMODEL製 3Dプリントキットアメリカ T1E1軽戦車 昨日(2024年9月16日)、組立開始です。 実車は、アメリカで1928年に4両生産されています。ルノーFT軽戦車の後継車両の開発ということで試作されたT1軽戦車の系列で、筒形の旋回砲塔にM1918 37 mm 短戦車砲とブローニング M1919 7.62 mm 機関銃を装備しています。キットは、3Dプリンタキットなので、例によって、サポート材の除去から行いました。超音波カッターも使って、慎重に作業しました。一体となった履帯・車輪関係は、かなり繊細でした。部分的に折れてしまったところもありますが、瞬間接着剤で修正できました。車体に一体成型されている排気管が部分的に硬化していなかったので、UVライトを当てて硬化させておきました。サポート材を除去し、部品が整ったところです。部品数が少ないので、除去したサポート材も、それほど多くありません。後部のハッチの把手を折ってしまったので、真鍮線で付け直しました。ヘッドライトとボディーを繋ぐ板の部分がモールとされていなかったので、プラ板にプラ棒でリベットを付けたものを自作して取り付けました。全体を仮組してみました。昨日の作業時間は1時間30分です。
September 17, 2024
閲覧総数 144
13
鳥取県の自宅に戻っていて最低限の工具と接着剤しかない状態ですが、中国のSSMODEL製1/35スケールアメリカ M2中戦車が届いていたので、ちょっと組んでみることにしました。3Dプリントのキットです。主要な部品は出来る限り一体成型になっているので、主な作業はサポート材の除去と下地処理、塗装になります。エンジングリルのメッシュのエッチングパーツ、真鍮挽物のアンテナ基部、デカールも入っています。車体の主要部です。驚くほど、一体に成型されています。サポート材を除去して、こうなります。工具やライトも一体成型です。車輪関係です。これまた、サスペンションと各車輪、履帯が一体成型です。サポート材を除去して接合部を調整して車体に仮止めした状態です。砲塔は、3つの部品で、この状態です。星形エンジンとエンジン飾り台が付属していますが、車体に組み込むことは無理です。昨日の作業時間は1時間10分です。
November 4, 2023
閲覧総数 255
14
タミヤ1/35スケールミニタリーミニチュアシリーズNo.318フィンランド軍突撃砲 BT-42タミヤ 1/35 MMシリーズ No.318 フィンランド軍突撃砲 BT-42【35318】 プラモデルこのキットをガールズアンドパンツァーの劇場版最終章第4話に出てきた継続高校のスキーバージョンに改造するパーツのセットプラッツから発売の「BT-42 継続高校 スキーVer.改造パーツセット」が届きました。3Dプリントの履帯とスキーの部品、継続高校のデカール、フラッグ用金属線のセットです。それではということで、タミヤのBT42のキットと一緒にしておこうと、自宅で段ボール箱に入れて積んであるプラモデルの、ここら辺にあると思うところを少し探しましたが、見つけられませんでした。数年前に購入している記憶があるので、エクセルで整理しているプラモデル購入記録を見て確認したら、2021年にブロンコのBT用履帯と一緒に他購入しています。また、時間があるときに、探してみることにします。ちなみに、タミヤのBT-42のキットは、発売直後に組んだことがあります。2011年ということで、もう13年前になります。前年にはイースタンエクスプレスのBT-42も組んでいます。その時の記録はこちらをクリックです。(当時は楽天ブログに画像の総容量の制限があったため、一部画像を削除していました。)
August 12, 2024
閲覧総数 176
15
本年46個目のプラモモノクローム(横浜市港北区)から発売の 1/35 スケール陸上自衛隊 75式自走155mmりゅう弾砲本日(10月30日)、組立開始6日目で完成です。本日は、午前中に砲塔の組立を終え、基本色のブランんの塗装を済ませておき、夜に迷彩塗装、灯火類や牽引ワイヤー、予備キャタピラ、機銃等の色入れ、デカール貼り、艶調整、汚しを行って完成としました。本日の作業時間は、午前に1時間20分、夜は午後7時50分から午後8時50分までと午後9時40分から午後10時20分までの40分の1時間40分、合計3時間です。完成までの累計作業時間は10時間10分です。キャタピラは連結可動式なので持ち上げると、このように弛みます。大きさの比較のために、タミヤのゼネラルセットのモンゴメリ元帥と前作のT型フォード救急車と並べてみました。
October 30, 2016
閲覧総数 448
16
本年17個目のプラモ 中国のタコム製 1/35スケール ドイツ試作重戦車 マウスV1 本日(4月17日)、組立作業7日目で完成です。 本日は、10分間で汚しを行い、完成としています。完成までの累計作業時間は11時間30分です。 汚しは、雨による水の流れと排気の煤汚れを考慮しました。 足回りは、車輪部分に少し埃汚れを付けています。 サスペンション、履帯が可動です。各車輪も回転します。キットにはフィギュアは付属していません。 タミヤのデマークのフィギュアや「ドイツ戦車兵小休止セット」のジャンク品などから組んだ戦車兵を載せてみました。1体は砲塔の手すりを掴んでいる状態にしてみました。 持ち上げると履帯がたるみます。
April 17, 2017
閲覧総数 401
17
朝ごはんヤマザキの洋菓子「5つに切ったロールケーキ(チョコ)」です。「チョコスポンジにバニラクリームを巻き込んだ、ふんわりとしたロールケーキです。」という解説書きがあります。熱量は476kcal、製造はヤマザキ名古屋工場(名古屋市西区)です。
August 8, 2020
閲覧総数 194
18
今朝は午前4時30分に起床です。昨夜から継続してエアコンの冷房を27度設定で稼働させていて、起床時の室内の温度・湿度は28.5度、49%、外気温は26.4度、天候は晴れです。起床時の血中酸素飽和濃度は96%、体温は36.6度でした。午前5時45分にGH3インプレッサで福山市内の住居を出発、国道二号線で福山西インターから山陽自動車道に入り、尾道自動車道、松江自動車道、国道54号線、国道9号線を走って自宅に戻りました。自宅の到着は午前9時03分です。福山市の住居を出発時に燃費計をリセットして、燃費は15.4km/Lです。国道9号線に入る前の燃費は15.7km/Lだったのですが、以降、エアコンを使ったので、燃費は少し落ちました。昼ごはん午前11時過ぎにイオンモール日吉津に行って、フードコートのいきなりステーキでコンボ250です。本日は、お肉の部位が大変に良かった(たぶんイチボです。)ので、かなりのお得感がありました。エディオン米子店に行って、模型用塗料を買ってから、境港市内に行って用事をしてきました。時々雷鳴がして豪雨でした。バタバタ走ったりしたら、かなり疲れました。午後3時過ぎに自宅の戻っておやつヤマザキの洋生菓子「ダブルクリームシフォン」です。頭痛と酸欠感がするので、少しのつもりで昼寝をしました。気付いたら午後6時でした。晩ごはん鯛(天然)のお刺身(湯引き)、焼ピーマン、千枚漬け、切り干し大根、キャベツサラダです。午後7時半過ぎ、血中酸素飽和濃度を測定したら92%でした。再測定しても同じです。
August 24, 2024
閲覧総数 120
19
モノクローム(横浜市港北区)から発売の 1/35 スケール陸上自衛隊 75式自走155mmりゅう弾砲昨日(10月28日)で組立開始4日目です。車体上部と下部を接着してからライトカバー等を取り付け、キャタピラを履かせました。砲塔の基本形も組みました。昨日の作業時間は、午後10時00分から午後11時30分までの1時間30分です。累計作業時間は6時間20分です。
October 29, 2016
閲覧総数 258
20
本日20個目のプラモウクライナのICM 製1/35スケール ホルヒ108 タイプ40本日(5月31日)、組立作業5日目で完成です。本日は、午後4時00分から午後5時50分までの2時間半で、ボディへの部品取り付け、デカール貼りを行い、夜、10分程で整等を行って完成としました。本日の作業時間の合計は2時間00分です完成までの累計作業時間は6時間50分です。ボンネットの上部は、はめ込むだけで取り外し可能です。(実車は真ん中から左右に上に向けて開く構造です。)前前作のホルヒkfz.15、前作のホルヒタイプ1aと並べてみました。タイプ1aタイプとタイプ40では、ボティの予備タイヤの位置以外に、シャーシの四輪操舵機構の有無が大きな違いです。(上1a、下40))
May 31, 2015
閲覧総数 1334
21
ゲッコーモデルス製 1/35スケール 巡航戦車A10 Mk.1A 昨日(7月26日)で組立作業15日目です。 デカールを貼りました。貼りやすいデカールですが、念のため、はがれ防止のためにタミヤのデカール糊を使いました。フィギュアの塗装も済ませました。昨日の作業時間は40分です。 累計作業時間は19時間50分です。
July 27, 2018
閲覧総数 350
22
本年36個目のプラモ ミニアート製 1/35スケール AVRO 671 ROTA MK.1 RAF 昨日(2019年10月23日)、組立開始です。1/35 アヴロ671ロータMk.1 RAF【MA41008】 ミニアート 第二次大戦当時のイギリスのオートジャイロで、英国空軍で使用された機体をモデル化したものです。 キットは、数か月前に発売されたものですが、その後、民間型なども発売されています。 キットの部品構成を見ると、足回りやローター基部など、強度的に心配です。組立説明書に沿ってエンジンから組みました。細かいエッチングパーツがあって、クラクラしてきます。部品の接合部のガイド穴が合わせる部品の突起と合わないなど、ミニアートらしい詰めの甘さがあるキットです。 昨日の作業時間は50分です。
October 24, 2019
閲覧総数 176
23
ここのところ、AFV関係のプラモばかりを組むと、頭の栄養が偏りそうなので、他のジャンルのプラモもできるだけ組むように心がけています。ということで、自宅でプラモの整理(というか散らかし)をするに際して、飛行機やバイクのキットも組みたいと思うものを手の届く位置に移動させています。書籍なども整理していますが、書籍の場合、一度、読みだすと、もう作業が止まってしまいます。昨夜、「20世紀飛行機プラモデル大全」をパラパラめくっていたら、結局、2時間以上、見てしまうことになりました。この本、出版は2004年です。10年前くらいに購入したような記憶でしたが、もう20年を経過していました。モノクロームのキットも載っていました。1/144スケールの九七式大型飛行艇23型のキットを、そろそろ組みたいと思って、先週、リビングに出してあったのですが、このキットも、もう20年以上前に発売されていたのだと、改めて、月日の経つの早いのだと思ってしまいました。
September 16, 2024
閲覧総数 148
24
今朝は午前5時30分に起床です。起床時の室内の温度・湿度は18.9度、53%、外気温は10.7度、 天候は晴れです。 起床時の血中酸素飽和濃度は92%でした。なんとなく、お風呂場に怪しい気配がしていたので、見てみたら、火星怪獣ではなくて、ナメクジが壁面のタイルを動いていました。糞もしていて、不気味悪いです。直ぐに排除しましたが、二階まで、どうやって上がってきたのか不思議です。午前6時52分に住居を出て、 午前7時30分に職場に到着です。 地下鉄の車内で少しクラクラしていて、職場に着いた直後に血中酸素飽和濃度を測定したら81%でした。昼ごはん魚肉ソーセージ、バナナ2本、マシュマロです。昼休み運動のために40分歩いてきました。職場に戻って血中酸素飽和濃度を測定したら94%でした。定時で帰って、住居に戻って血中酸素飽和濃度を測定したら93%でした。晩ごはんの焼そば麺は大黒天物産のプライベートブランドの蒸し麺 、 具は大山ハム(鳥取県米子市)のポークウインナー、キャベツ、たまねぎ、にんじんです。 じゃこ天、ミニトマト、めだまやきを添えました。 別添でヒジキ煮、ポテトサラダがあります。
May 6, 2021
閲覧総数 522
25
本年40個目のプラモ トランぺッター製 1/35スケール ブラジル陸軍 EE-T2 オソリオ 本日(2021年10月5日)、組立作業5日目で完成です。 本日は、艶調整、汚し、アンテナ線の取付けを行いました。 本日の作業時間は20分です。 完成までの累計作業時間は5時間50分です。サイドスカートは、分割線に墨入れしてありますが、目立たないので、ウェザリングマスターでヒルマ汚し風にしてみました。ドライバーズハッチ、砲塔のコマンダーズハッチは開閉可動に加工しました。ローダーズハッチは、キットのままで開閉可動になっています。アンテナ線は0.75㎜プラ棒で自作です。このキットは、120㎜砲と105㎜砲の砲身が付属しています。これまでの画像は全て120㎜砲を装備した状態ですが、差し込むだけにしてあるので105㎜砲にも差し替えできます。履帯は軟質樹脂のベルト式ですが、ディティールはこれで十分です。大きさ比較のため、タイガー1型と並べてみました。
October 5, 2021
閲覧総数 399
26
今朝は午前5時20分に起床です。エアコンを27度設定で稼働させて、床時の室内の温度・湿度は28.9度、51%、外気温は25.6度、天候は概ね晴れです。起床時の体温は36.6度、血中酸素飽和濃度は97%でした。午前6時50分に運動のために歩きに出かけて、いつもの猫スポットまで往復してきました。本日は某マンションの黒猫2匹と近所の三毛を確認です。この猫は、見事に熟睡していたらしく、声をかけてもなかなか反応しなかったので、死んでいるかと思ってしまいました。もう一匹は、声をかけたら起きました。近所の三毛はお食事中でした。いつもの時間よりも、20分早く出勤し、直ぐに仕事を始めました。昨日の外部監査で処理できなかった書類の処理で、あっという間に昼になりました。昼ごはんいつもの給食弁当です。メインのおかずは、牛肉入りコロッケとソース焼そばです。ゴボウやレンコンを使ったおかずもあって、繊維質も摂れて美味しくて嬉しいです。昼休み時間、少し目を休めるため、外に出て、カニを見てきました。午後からも、書類の処理であっという間に時間が経ちました。対外的な書類の処理は、なんとか停滞は解消しましたが、内部的な書類の処理は、一部、明日に回しました。ほぼ定時で帰って、住居に戻って血中酸素飽和濃度を測定したら94%でした。晩ごはんの焼そば麺は藤本食品の蒸し麺、具は牛チャック&ブレード、ニンニクの芽、もやし、キャベツ、ピーマン、ニンジンです。がんす、ミニトマト、めだまやきを添えました。別添でアジフライがあります。
September 18, 2024
閲覧総数 100
27
本年57個目のプラモロシアのVM 社 製 1/35スケール 25ポンド 自走榴弾砲 ビショップ本日夜(12月5、日)、組立作業7日目で完成です。本日は、アンテナ類を塗装してからデカール貼りを行い、全体に軽く汚しをかけて仕上げる作業を行い、完成としました。キット付属のデカールは、シート全体がニス部で全部つながった状態であることに気づかないで水につけてしまったため、水を吸って軟らかくなった状態で必要な部分を切り離すことが出来ず、使うことをあきらめました。代わりに、前作のブロンコモデルのビショップの組立で余ったデカールを使いました。本日の作業時間は1時間20分です。完成までの累計作業時間は12時間20分です。マーキングは1942年のリビア戦線の第121砲兵師団のものですが、車両の形態と貼った番号が合っているとは限りません。砲塔のハッチ類は、開閉可動にしてあります。前作のブロンコモデルのビショップと並べてみました。VMモデルの製品は20年くらい前のものですが、かなり良い出来だと思います。天井のハッチの形状、換気扇の位置などが異なります。(ブロンコモデルのキットには砲塔の天井は2種類から選択するようになっています。)
December 5, 2011
閲覧総数 793
28
アミュージングホビー製 1/35スケール ドイツ 12.8cm Flak40&ウルツブルクレーダー FuMG39D 昨日(11月5日)で組立作業2日目です。 砲耳、自動装てん装置等を組みました。昨日の作業時間は1時間00分です。 累計作業時間2時間50分です。
November 6, 2018
閲覧総数 180
29
本年4個目のプラモ タミヤ 1/35スケール ミニタリーミニチュアシリーズNo.125 トウミサイルランチャー1/35 アメリカ M151A2 トウミサイルランチャー 【35125】 タミヤ [タミヤ.M151A2トゥミサイルランチャ]【返品種別B】 本日(1月28日)、組立作業4日目で完成です。 本日は、塗装の仕上げ、透明部品の取り付け(ヘッドライトのレンズはUV硬化樹脂を流してUVライトを照射して固めてあります。)、デカール貼り、艶調整を行いました。 本日の作業時間は1時間20分です。 完成までの累計作業時間は5時間20分です。
January 28, 2018
閲覧総数 620
30
本年28個目のプラモ タミヤ・イタレリ製 1/35スケール ドイツ連邦軍M47パットン 本日(2020年7月17日)、組立作業7日目で完成です。 本日は、艶調整、汚しを行いました。 本日の業時間は20分です。 完成までの累計作業時間は6時間40分です。マーキングはドイツ連邦(西ドイツ)軍の1960年代のものです。ローダーズハッチとトラベリングロックの砲身固定部は非可動でしたが、可動に加工してあります。キングタイガーと並べてみました。M47はそれなりに大きいと思っていましたが、こうして並べると、キングタイガーのほうがかなり大きいです。
July 17, 2020
閲覧総数 408
31
鳥取県の自宅に戻っていて、今朝は午前4時50分に起床です。起床時の室内の温度・湿度は24、1度、54%、外気温は16.2度、天候は曇りです。起床時の血中酸素飽和濃度は97%、体温は36.4度でした。先週の金曜日にJR福山駅でICOCAが磁気異常で使えないことが判り、再発行登録証が発行され、昨日、JR松江駅のみどりの窓口て再発行を試みましたが、京都市交通局の窓口に行かないと再発行できないということだったので、本日、京都まで行くことにしました。京都在住の際に時々食べていた京都の七条烏丸西入ルの菓子店「松屋」のおはぎも食べたかったので、併せて買いに行きます。午前6時34分にLA160ステラで自宅を出発、米子自動車道、中国自動車道、新名神高速、名神高速を順調に走って、午前11時過ぎに、ジョーシン九条烏丸店の駐車場に到着、地下鉄九条駅から京都駅まで一駅地下鉄に乗って、京都駅の京都市交通局の定期券発売所で、スムーズにICOCAが再発行されました。券面のデータは2年前のままです。ICOCAのカードの模様が京都市交通局のものになりました。七条烏丸西入ルの菓子店「松屋」には、午前11時半頃に行き、無事におはぎを買うことができました。以前と変わらず、1個350円(税込)でした。昼ごはんは、ヨドバシ京都店の6階にある風月で豚玉モダン焼を食べました。ヨドバシを一通り見て回ってから、地下鉄で九条駅に行き、ジョーシン九条店の模型売場を見てから、午後1時過ぎに、九条烏丸を出発して、鳥取県の自宅に向かいました。途中から雨でしたが、渋滞に遭うこともなく、午前6時過ぎに自宅に到着しました。朝、出発時に燃費計をリセットしていて、往復で約600km走っていて、自宅に戻った際の燃費は23.0km/Lでした。往路の途中からエアコンを使い、帰路は雨だったことを思えば、良い数値です。晩ごはん松屋のおはぎを主食にして、おかずは、筑前煮、豆腐ハンバーグ、ポテトサラダです。いちごは、勝央サービスエリアで購入したもので、1個250円位でした。とても良い香りがしていて、思わず買ってしまいました。
April 29, 2024
閲覧総数 168
32
今年の4月7日に完成させた中国のSSMODEL製の3Dプリントキットソビエト SU-8 対戦車自走砲ですが、その後、ずっと室内に飾ってあります。今朝、気付いたのですが、エンジンファンのカバーと車体の間から、何やら液体が染み出て流れた後があり、部分的に、まだ濡れて状態でした。染み出た液体は、下に敷いてあるカッティングマットも汚していました。染み出た液体は、溶剤臭はしませんが、綿棒で拭き取ったら、下の塗装も剥げました。UVライトを照射しても固まりません。一体何なんでしょう。
September 10, 2024
閲覧総数 188
33
今朝は午前5時30分に起床です。エアコンを27度設定で稼働させて、床時の室内の温度・湿度は29.0度、56%、外気温は25.7度、天候は晴れです。起床時の体温は36.4度、血中酸素飽和濃度は96%でした。午前6時50分に運動のために歩きに出かけて、いつもの猫スポットまで往復してきました。本日は某マンションの黒猫3匹と近所の三毛を確認です。いつもの時間よりも、20分早く出勤し、直ぐに仕事を始めました。先週の木曜日、金曜日が出張で職場に出ていないので、書類が溜まっていて、大変なので、自動販売機で、キリン・ファンケルのカロリミット・アップルスパークリングを飲んで、がんばりました。更に、本日は、午前9時から社外監査があるので、資料等の準備はしてあるので、慌てることはないのですが、自分の持ち分を説明するだけで、午前中があっという間に過ぎました。沢山しゃべったので喉が疲れ増した。昼ごはんいつもの給食弁当です。メインのおかずはチジミと揚げ餃子です。午後3時前まで監査の対応で、その後、ルーティの事務作業だったので、かなり疲れた感じです。本日は、中秋の名月なので、スーパーで月見団子を買って晩ごはんの後で月見をしながら食べるのを楽しみにして頑張りました。ほぼ定時で帰りました。帰りに寄ったスーパーで、乱暴な曲がり方をしてきて、こんな停めかたをするアルファードがいました。通路が狭くなって迷惑です。運転している人を見たら、人のことなんか考えない(考えることができない)人だと一目で判る容姿の子連れ女性でした。住居に戻って血中酸素飽和濃度を測定したら96%でした。晩ごはんの焼そば麺は藤本食品の蒸し麺、具は牛チャック&ブレード、ニンニクの芽、キャベツ、もやし、ニンジンです。がんす、ミニトマト、めだまやきを添えました。別添で厚揚げがあります。本日から、またミカンもあります。中秋の名月なので、月見でお団子を食べます。今年は、ヤマザキの月見団子です。熱量は215kcal、製造はヤマザキ岡山工場です。東の空に見える、本日の月です。スマホに、安い望遠レンズをつけて撮影しました。月見団子の一番上のように黄色い月です。
September 17, 2024
閲覧総数 127
34
中国のSSMODEL製 3Dプリントキットアメリカ T1E1軽戦車 昨日(2024年9月17日)で組立作業2日目です。全体の塗装を行いまいした。全てタミヤの水性アクリル塗料で筆塗りです。履帯はダークアイアン、車体はオリーブドラブです。排気管はダークアイアンにNATOブラウンを混ぜて調色した錆色を塗っています。昨日の作業時間は50分です。累計作業時間は2時間20分です。
September 18, 2024
閲覧総数 107
35
ファインモールド製1/35スケール 高機動車(キャンバストップ)昨夜(3月24日)で組立作業2日目です。メーターパネル等にデカールを貼ってから、車体の組立の続きを行いました。昨夜の作業時間は午後11時00分から午後11時50分までの50分間でした。累計作業時間は3時間30分です。
March 25, 2014
閲覧総数 327
36
本年62個目のプラモトランペッター社製1/35スケールドイツ VK30.01(H) 試作戦車昨日(12月24日)、作業4日目で完成です。昨日までにデカールを貼るところまで済んでいたのですが、追加でタイガー戦車の初期型を参考に、砲塔のキューポラのハッチに真鍮線で把手を付けておきました。その後、デカールを貼った上から艶の調整を行って完成です。三号戦車と六号戦車(タイガー戦車)の過渡期的な形状となっています。国籍マークや砲塔の数字は、実車で記入している写真は見たことがありませんが、試験的に実戦参加していたら、こんな感じだろうということで、適当につけていみました。砲塔内部も再現されているので、トンボの「ピッとマルチ2」をハッチのヒンジ部分に塗って乾燥させておき、粘着力で保持するという簡易な方法によりハッチを開閉できるようにしてあります。エンジンデッキの状態など、やっぱり、三号戦車の拡大版という感じです。
December 25, 2008
閲覧総数 166
37
アカデミー製 1/35スケール イスラエル戦車 マガフ7C ギメル 昨日(9月23日)で組立作業5日目です。砲塔バスケットに取付けるマーキング用のキャンバスを紙で自作してから、砲塔の塗装を行いました。予備履帯、ポリタンク等も塗装しました。塗装した牽引ワイヤーを砲塔に取り付けようとしたら、長さが1cm程足りません。組立説明書の指示に従ってキット付属の糸を14cmに切ってアイ部に取り付けたのですが、アイ部への取付けシロ部分各5mm程度は14cmに含まれていなかったようです。木綿糸でワイヤー部を作り直すことにします。昨日の作業時間は、午後10時00分から午後11時20分までの1時間20分です。累計作業時間は9時間50分です。
September 24, 2016
閲覧総数 442
38
本年57個目のプラモイタリアのイタレリ社製1/35スケール アメリカ陸軍 M32戦車回収車今夜(11月17日)、ワイヤーなどの調整と汚し塗装をして完成しました。M32戦車回収車はM4A1シャーマン戦車を改修してクレーンブームやウインチ等を装備した車両です。45個目に作ったシャーマン・マインローラーと同じく、「今週のびっくり・ドッキリメカ発進」という感じです。今回は、クレーンブームを起倒させられるように改造してあります。ウインチのワイヤーを車内から出せるように改造すれば、さらに面白かったかもしれませんが、それは、また次回の組み立て時(何年先になるか判りませんが。)に挑戦します。クレーンブームを倒した状態です。クレーンブームを起こした状態です。クレーンブームを起こした状態での車体前部のアップです。右側起動輪に取り付けてあるリムにブームから伸びるワイヤーの端(模型では車体側に取り付けてある。)を取り付けて、起動輪を回すことで、クレーンブームを起こしたり倒したりすると思われます。クレーンブームを起こした状態で前方を見たものです。迫撃砲が取り付けてありますが、これは煙幕弾を発射するために使うそうです。車体の砲塔のようなものは固定式の作業室で、予備転輪や起動輪のギアなどのスペア部品が取り付けてあります。前方上部には車体内部のウインチから延びるワイヤーを通すガイドの穴があります。ウインチからのワイヤーは、車体のギアハウジング上部にある取り出し口からも引き出せ、そこからのばしたワイヤーはウインチとして使えます。そのためのガイドローラが迫撃砲の下部分にあります。(四角い穴のようなところ。)クレーンブームを倒した状態です。車体後部に固定する部分があります。作業室のハッチはヒンジに真鍮線を仕込んで開閉できるようにしてあります。
November 17, 2008
閲覧総数 206
39
アカデミー製 1/35スケール イスラエル戦車 マガフ7C ギメル 昨日(9月22日)で組立作業4日目です。午後、作業時間1時間で、前日までに組んだ部分の基本塗装を行いました。転輪のゴム部の塗分けも済ませました。車体色のシナイグレーは、以前にマガフ6を組んだ際にタミヤの水性アクリル塗料で調色してあったものを使用しました。午後9時50分から午後11時30分までの1時間40分で砲塔の組立の続きを行い、ほぼ部品の取付けは終わりました。昨日の作業時間は、合計2時間40分です。累計作業時間は8時間30分です。
September 23, 2016
閲覧総数 715
40
本年43個目のプラモ中国のモンモデル(MENG MODEL)製1/35スケールイギリス重戦車 Mk.V MALE 本日(10月27日)、組立作業9日目で完成です。本日は、塗装の微修正と履帯の取付けを行っています。塗装後の履帯は連結部が外れて、何度もきれてしまいます。取付けだけでかなり時間をとりました。更に、また、手が滑ってスポンソンの機銃を折ってしまいました。そんなことをしていて、本日の作業時間は、午後9時50分から午後10時30分までの40分です。完成までの累計作業時間は20時間00分です。このキット、内部構造再現モデルですが、各種配管やレバーから延びるロッドなども、しっかりと再現されており、そら内部の機構が車体外部の構造物とどのような関係にあるのかとか、砲弾や機銃弾の収納場所が、よく考えて設定してあるということが判り、面白かったです。キャタピラの連結が外れやすいことだけは、残念ですが、価格に見合った良いキットだと思います。今回は、汚しをかけていません。超壕装置を載せた状態で博物館に飾ってあるというような感じです。信号機の支柱は基部にポリキャップが仕込まれていて、上下動可能となっています。頂部装甲板の後部にあるハッチは接着せずに、ヒンジ部にトンボの糊「ピットマルチ2」を塗って止めてあるので開閉可能です。側面のスポンソンは、車体に接着しなくてもカチッとはまるので、外して内部を見ることができます。ホイペットと並べてみました。大きさ比較のために、タミヤのゼネラルセットのモンゴメリー将軍を立たせてます。
October 27, 2015
閲覧総数 514
41
朝ごはんヤマザキの食パン「レーズン好きのレーズンブレッド」です。1斤340グラム、100グラム当たり熱量277kcalということなので、1斤1包で940kcal、6枚切で1枚あたりの熱量は概ね150kcalです。製造はヤマザキ京都工場です。
May 27, 2015
閲覧総数 121
42
本年19個目のプラモ中国のブロンコモデルク社 製1/35スケール フラックワーゲン4c型8.8cmFlak41搭載高射自走砲昨夜(6月3日)から組立作業開始です。8.8cmFlak41搭載高射を搭載した自走砲で、車台はIV号戦車や18トンハーフ「ファモ」の車輪などが流用されています。試作車が1944年にイタリア戦線で実戦投入されたということです。グランドパワー別冊「ドイツ軍試作車両」などに車写真が載っていたので、以前から存在を知っていましたが、まさか、こんな車両までがインジェクションキット化される時代が来るとは・・・。部品数が、絶望的に多いですが、砲部分の部品が、とにかく細かいです。キャタピラは連結組立可動式です。トーションバー式サスペンションも可動です。組立説明書の指示に従って、サスペンションから組み始めました。トーションバーアームはスケール通りなのでしょうが、このまま可動状態で組むと、強度がなくて、たぶんヘタリます。最前部と最後部のサスペンションは固定することになりそうです。昨夜の作業時間は、午後11時00分から午後11時間40分までの40分です。
June 4, 2013
閲覧総数 3181
43
本日のおやつ川崎市宮前区宮崎2-12-1にある洋菓子店「ロワール」で買ってきたたぬきケーキです。横浜に引っ越してきて、たぬきケーキ探索の第3弾です。本日、川崎の模型店の閉店に合わせて川崎に出かけたのですが、気温が低かったので、たぬきケーキも買いにゆくことにしました。川崎駅から南武線の電車の乗って、武蔵溝野口駅で田園都市線に乗り換え2駅で宮崎台の駅に到着です。お店は、駅前のマンションの1階、改札から歩いて90秒でした。たぬきケーキは、「ロールケーキ」という名称で販売されていました。たぬきケーキは2個を買い、併せて、上に並んでいた「サバラン」も買いました。たぬきは1匹280円、サバランは1個260円でした。たぬきケーキの構造は、胴体部分がチョコロールケーキ、頭が中はチョコアジのバタークリーム、耳はチョコプレートです。住居に持って帰って箱から出す際に、たぬき1匹の耳を折ってしまいました。たぬきケーキは、あっさりしているので、2個ともペロリと食べてしまいました。サバランは、お店のポップに「洋酒がたっぷり」と書かれてあったとおり、スポンジにたっぷりの洋酒で、マロングラッセがのっています。下部分はメレンゲのようなゼリーです。これも美味しかったです。
June 2, 2013
閲覧総数 1487
44
タミヤの1/35スケール MMシリーズNo.213 キューベルワーゲンをベースにした装甲車昨夜(2月1日)で組立作業9日目です。砲塔にプラ板等でリブや覘視孔(てんしこう)を付けました。機銃はドイツ四号戦車車外装備品セットのものを使用しました。後、砲塔にはリベットを取り付けます。昨夜の作業時間は、午後10時10分から午後11時50分までの1時間40分間です。累計作業時間は10時間20分です。
February 2, 2014
閲覧総数 414
45
朝ごはんフジパンの菓子パン「ホテルトースト シュガーマーガリン」です。熱量は293kcal、製造はフジパン東京工場(埼玉県八潮市) です。
October 12, 2018
閲覧総数 356
46
朝ごはん第一屋製パンのドーナツ「シュトーレン風ドーナツ 2個入」です。「ラムレーズン・りんごジャム・オレンジピールとオールスパイスを練り込んだシュトーレン風のドーナツです。」という解説書きがあります。熱量は1包504kcal(1個252kcal)、製造は第一パン小平工場(東京都小平市)です。
December 27, 2019
閲覧総数 227
47
朝ごはん おはぎ つぶあん きなこです。製造はアルプス(奈良県葛城市)、 熱量は1パック409kcalです。
May 2, 2020
閲覧総数 414
48
本年2個目のプラモ ICM製1/35スケールFCM36本日(2021年1月13日)、組立作業5日目で完成です。 本日は、墨入れ、艶調整、汚しを行っています。 本日の作業時間は20分です。完成までの累計作業時間は7時間30分です。砲塔後部ハッチは、開閉可動に加工しました。タミヤのR35戦車と並べてみました。大きさ比較のため、KV-2、ジープと並べてみました。
January 13, 2021
閲覧総数 431
49
朝ごはんヤマザキの新製品「切れ目が入ってちぎりやすい!レーズンフランスパン」です。「レーズンを練り込んだ生地をフランスパン生地に包み焼き、『切れ目を縦と横』に入れた後、ミルク風味クリームをしぼり、しみ込む様に焼き上げました。」という丁寧な解説書きがあります。熱量は410kcal、製造はヤマザキ広島工場です。
April 2, 2022
閲覧総数 280
50
本年3個目のプラモ タミヤ 1/35スケール ミニタリーミニチュアシリーズNo.95 日本陸軍 一式砲戦車本日(2023年1月29日)、組立作業6日目で完成です。本日は車体の塗装の艶調整と付属の戦車兵の塗装の仕上げを行いました。本日の作業時間は30分です。完成までの累計作業時間は5時間50分です。九七式中戦車、九五式重戦車、オイ車と並べてみました。
January 29, 2023
閲覧総数 222