全30件 (30件中 1-30件目)
1
今日は結構疲れました。疲労?やっとこさ家人がPS2をSCEIの修理に出すことになりました。というのも、最近出たゲームが出来ないという単純な話。買い換えだと高いし、自分でピックアップを手に入れて交換するのは直る保証がないし(壊したら殺られる!)、だからといってばらしてレーザー出力調整を行うのも面倒なので。とりあえず受付カルテ記入。使用していたテレビ欄は見栄を張ってSONYのプラズマVEGAの形式を書いてやりましたよ。少しは安くならないかなぁみたいな。あとは着払いで送りつけるのみ。面倒です。ゲーム機も面倒な世の中です。昼寝しようとしたのに寝忘れてしまってブルーな管理人でした。ネタ切れつまらない日記勃発中。
September 30, 2003
コメント(2)
限りなく平凡な一日でした。ちょっと暑かったのですが。学校でいつものようにモバイルメールサービスでメールチェックを行ったところ、EPSONから「無償ドアtoドアサービス終了間近!」のようなメールが届いておりました。どうやら去年の文化祭の終わった日に購入したColorio PM-740Cが対象商品になっていたようで。無償サービスなので勿体ないと思い、家に帰ってから申し込み。年賀状シーズンに向けてメンテナンスに出そうと思ったので。今週の土曜日に引き取りに来るそうです。元気になって戻ってこいよ、My EPSON Colorio(ぉ
September 29, 2003
コメント(0)
今日はLGコンボでコースターを作りまくってしまいました。というのも、Cl*neCDで某CDの作成を試みていたのですが作成自体は出来るもののそのCDを実行するとプログレスバーが途中で止まってしまいエラーで終了するからです。一枚目:普通に焼いてみた。エラーで使用できず。二枚目:HDDの空きを増やしてから焼いてみた。エラーがでるまでの時間が長くなった。三枚目:レンズクリーニングをして16倍速固定で焼いてみた。上記同様。四枚目:面倒になりCD-RWに焼いた。成功。しかし腑に落ちない。五枚目:ツインドライブ装備のVALUESTARでオンザフライ。成功。と言うわけで、CD-Rメディア三枚浪費!いったいなんだったんだ・・・。一日潰れてしまいました。ううむ。
September 28, 2003
コメント(0)
今日はまたごく普通の休日でした。昨日心配していたビデオ録画もきちんと行われていたので。問題があったとすれば時計が2分ずれていたことでしょうか?昼寝をしまくってしまいました。3時間以上寝ていたようです。秋らしい過ごしやすい天気で、かなり爆睡。午後からデジカメで暇を持て余していました。なんとなく外の木蓮の木の上端部を撮影したらかなりいけてる写真になったので上げておきます。これに文章を入れたらもっと良い感じの写真になりました。かなり自己満足。ううむ。家人がCDのジャケットにしてとか言ってたりします。ついでに家人2のPCに先日購入したMELCOのコンボドライブを取り付け。簡単でした。しかし、Windows上ではやはり簡単には行かず、WinDVDをインストールしてみたものの再生時に音声が再生されたとたんにフリーズします。CD-R/RW書き込み機能はまだ試していません。もう面倒なのでFMV-6266DXを買ってしまいました。フロント部分はFMV-6300DX2cの方がかっこいいので、マザーだけそっくりそのまま移植することになりそうです。FM90AAなので富士通Siemensの最新BIOSが使えますし。ACPIもこれでOKそうです。あとはマザーのジャンパでISA内蔵サウンドを切って、PCIスロットに先日購入したCobra AW850を搭載する予定。これでDVDをアナログ音声6CH出力出来そうです。Windows2000なAptivaも未だに使用用途が見つからないと言うのは言えませんね・・・。
September 27, 2003
コメント(0)
今日はやはり雨が降っていました。最近天気悪いです。タイトルの通り録画機として使用していたPanasonic NV-SB600Wが先日の急な冷え込みで故障しました。もちろん原因は「結露」。テープを挿入して走行したところ速攻で止まるのでおかしいなぁと思って取り出してテープを触ったところ濡れていました。しかも肝心の結露表示は出ないし、数時間経って乾いたかと思ってテープをまた再生してみようとしましたが変わらず。テープの結露が乾いたのにテープに何か付着している様子。アルコールでふき取って再生してみましたが、トラッキングが合わず「クリーニングテープをおためしください」と表示される始末。ヘッドが逝ったかなぁとその場は断念しました。丁度明日は録画するものがあるのでちょっと危険ですがまだメンテナンスしていない日立7B-FV220を仮に設置して録画予約しました。早速NV-SB600Wを下ろし、分解。テープ走行系には異物の付着など無い様子。しかし、ヘッドの磁性体の上あたりに黒い線が入っています。汚れのようで。丁度足回りが旧型KメカだったのでNV-H10から摘出した新Kメカに交換。ローディングモーターやモードスイッチは前のKメカから移植。メンテ歴があるので。それで再び組み直してからクリーニングテープ二種をかけてテスト。何とか再生できるようになりました。が、下の方に周期的にノイズが入ったり入らなかったり・・・。古いのでピンチローラーも交換すべきなんでしょうかねぇ。まぁNV-SB600Wがまだヘッドの寿命じゃなくてよかったです。(でもNV-SB600WでS-VHS三倍で録画したテープをHV-S780で再生すると反転ノイズ出るんですけど・・・。)しかし、HV-S780と相性がよくないようなので別のデッキを購入していたりします。まぁ修理のしやすさから日立のテープナビのジャンクだったりしますけど・・・。これでやっとS-VHS ET録画が出来るようになります。
September 26, 2003
コメント(0)
今日は軒並みな天気でした。秋雨前線の影響をもろに受けまくった肌寒い一日で。とりあえず高校生活最後のプールの授業もめでたく終了し、世界史のテストも前日に友人から出る内容をピンポイントで教えて貰ったのでかなり出来て一安心。普通に家に帰りましたが、やはりVoIPアダプタは到着していませんでした。不審に思い、ファックスの着信履歴を確認すると見事に家族が誰もいない正午に佐川急便の営業所から連絡があったことが判明。折り返しかけ直して持ってきて貰いました。30分程度でお届けとはかなり迅速。早速設置。骨が折れまくりでした。コンセントが開いていなかったのもその原因でしょう。セットアップもかなり難航し、・UPnP対応ならなぜルーター越しで設定できない!接続できないと何度も繋ぎ変えては設定画面にログインしなくてはなりません。かなり面倒です。・設定画面のIPとVoIP接続に使うIPを同じ領域(例えば192.168.10.2と192.168.10.254)に設けるとVoIP接続が完了してもアラームランプがずっと点滅しっぱなし。VoIP接続側を変更すると家庭内LANのIPも全て変更しなくてはならなくなるので設定画面のIPを変更。これでわざわざ設定時には繋ぎ変えてIPを再設定する必要が。ちなみにファームを最新にしても変わりませんでした。それと、アラームランプが点滅していてもVoIP接続は確立しているのでVoIP通話が可能でした。・設定画面のIPを変更すると勝手にVoIP接続のIPアドレス類が動的に変更されます。かなり面倒。家のルーターはP2Pソフトを使う関係上DHCPを切って手動でIPを割り当てているための設定です。・@niftyフォンの自動設定スクリプトが正常に動作しない!ルーター越しでは出来ないようです。なんのためのUPnP対応アダプタだ!っと言いたくなります。・同じくNTTの自動ファームウェアアップデートも正常に動作しない!ルーター越し云々の前にスクリプトがおかしいです。VoIPアダプタのアドレス欄に設定し直した後のIPを入れても工場出荷時のIPにアクセスしやがります。何度やっても工場出荷時のIPに行くのでしびれを切らしてVoIPアダプタの設定画面から更新してしまいました。とりあえず今現在やっと使えるようになった感じです。AtermWM56に接続されているので、めでたくVoIP-PHS通話が可能になりました。なので、feel-H" RZ-J90からもIP電話が可能に。おもしろいかも。最後に総評。「サポート悪すぎ!」@niftyのサポートに連絡しても「担当が違います」と回されるし、最初のガイダンスが分かりにくすぎです。また、回された先も混雑で繋がらず。アラームランプ点滅はNTT東日本フレッツサポートセンターに連絡しろと書いてあるのに気づいたので、改めてそちらにかけ直したところ10分も繋がらず。再度かけ直しやっと繋がったかと思うと、なんだか頼りないサポート担当が出ました。いろいろ把握していないようで、こちらからかなり教えました。結局自動スクリプトをVoIPアダプタからPPPoE接続して試せという結論で終わったのですが、そこまでたどり着くのにかなり時間がかかりました。また、IPアドレスの重複の可能性にはふれていませんでした。やはり微妙なところです。これから一ヶ月国内通話無料!やった!追伸:FMV-6300DX2cで苦労しまくっている家人2がコンボドライブを購入。どうするつもりなんでしょうか?(ぉ
September 25, 2003
コメント(0)
今日は寒かったです。特にプールの授業があり得ませんでした。そのためさっさと帰宅。変わったことはメールで他の高校の友人が沖縄へ修学旅行へ行っているそうなのでお土産を頼んだくらいでした。今度こっちが修学旅行に行ったときにはお土産のお返しをしなければと思いました。という話は置いておいて帰宅完了。なぜかIP電話アダプタ(VoIPアダプタ)が配達されませんでした。午前中配達なのに午前中に家に人がいなかったのが原因のよう。とりあえず日再配達されるのを祈るしかなさそうです。ちなみに頭の中で構成を練っているIP電話システムですが、VoIP通話時はスプリッタのMODEM端子を音声データが通り、PSTN通話時はスプリッタのPHONE端子を通ってNTT回線を通ると言うこと(という勝手な解釈)なので、とりあえずスプリッタのPHONE端子に二分岐アダプタを取り付け、片方はVoIPアダプタを通してAtermWM56に接続し、もう片方は直接Speax N1CLに接続しようかと。そうすると居間のSpeax N1CLと純正子機はアナログ回線接続、AtermWM56を通った二階のPHS子機三台はアナログ・IP回線接続となるはずです。こうすれば疑似二回線化ができ(Speax N1CLでアナログ回線を使用中でもAtermWM56の子機からのVoIP通話が可能)部屋から電話使い放題のシステムが完成しそうで。なんて考えでいますが、実際はどうなる事やら。VoIPアダプタが到着しないことには始まりません。今週末までにはIP電話(@niftyフォン)のレビューらしきものを掲載できると思います。さて、タイトルのもう一方の話を書くことにします。というのも、ここのところ寒く朝方一階のLDKが冷え込むのでファンヒーターを出して暖房しようとしたときのこと。いつも通りに使おうとすると、着火時になって延々と放電音がなり、気化した灯油のガスが白煙となって吹き出しました。何度やってもつきませんでした。あきらめてエアコンの暖房に切り替えたのですが何か腑に落ちず、もう一度やってみたところあっさり着火。しかし、運転停止時に気化器のノズルの閉まる音(ガンッという音)がしないので明らかに故障だと。親も納得。と言うわけで買い換えるための機種探し。そろそろ電器店にも石油ファンヒーターが並び始めていますし。条件は、・メーカーは今までと同じダイニチ工業。・木造14畳以上に対応した50タイプを選ぶこと。と言った感じ。前回も同じような感じでした。捜査線上に浮かんだのはFW-5580EとFW-5580LD。昨日なぜか行っていた値段調査で、前者は24800円、後者は29800円と5000円の差。 さらに調査を進めると、前者は7.2Lタンクで電子油量計がなく、後者は9Lタンクで電子油量計装備な事が判明。ついでに5580LDはマイナスイオン発生装置付きのようです。親に相談すると、今の機種で電子油量系を便利に使っているため、やはり電子油量計は必要なそうで。と言うわけで買うならFW-5580LDに決定。展示機はシャインゴールドですが、部屋に合わないので買うならプラチナシルバーにするそうです。という風に親と相談しましたが、母は買い換え推進なのに対し父は修理に出せと言います。買い換えより安い場合ですけど。とりあえず明日アフターサービスにどれくらい修理にかかるか聞いてみることにします。98年製のFW-5020Dはどれだけかかるんでしょうね?ここまではコアな話でした。最後に今日気づいたこと。家の一本下の区画の公園の電柱にこんなものが付いていました。光クロージャーみたいです。やはりBフレッツ開通間近かもしれません。@nifty工事費無料キャンペーンはまだやっているので悩ましいところです。父が玄関の電話線が目障りと言うのでこの案を提出するのもいいかなと思ったりしてます。
September 24, 2003
コメント(0)
タイトルが物騒ですがご了承ください。とりあえず今日は祝日で休みでした。そのため、朝から昨日組み立て終わったAptivaの設定云々を。それにしてもAthlonは快適。Webページの読み込みがまるでぱらぱらめくるカタログのようにさくさくです。特に某個人売買サイトの写真一覧にした際の読み込み時間差は歴然。家の中で一番速そうです。そして唯一のAMDプロセッサ搭載機であったりします。ちなみにオンボードのProSavageグラフィックコアはヘボイです。3DMark2001SEのデモがカクカクだし、32bitTrueColorでDivX動画が駒落ちしまくり。全くi810e内蔵グラフィックに追いついていません。ここはPCI接続LowProfileなVGAを刺して解決する予定。Geforce4MX440SE(だったっけ?)あたり爆安みたいですけど、ちょっとむりしてRADEON9200SE搭載のを買った方がいいんでしょうかねぇ?それとVIA統合チップセットとGeforce系VGAは相性があるようですし。オンボードLANは死んでいるようなのでBIOSで使用しない設定に。Windows2000 Professionalはかなり快適でした。本題のFMV-6300DX2cのオンボードサウンドはがしの話でも。一言で「難しい!」に尽きます。そのまま半田吸い取り線を使ってもできないし、多めに半田を乗せてからやっても同様。面倒になったのでLSIの足をカッターで切ってしまいました。元には戻れません。2チップ構成のようですが、面倒なので大きいCS4614を引っぱがしました。早速起動してみるも、起動時のサウンドは鳴りますがWMPで音楽を再生するとフリーズ。やはり改良の余地ありです。というわけで疲れた休日でした。ここで終わるの物足りないのでもう一つ。家族で墓参りに出かけた帰り電器店に寄りました。最新の19型SXGA液晶がセットされたSONYのVAIO RZがありました。弄ろうとマウスを動かすも反応なし。いろいろやっても映像が出てこないので強制電源断。切れません。仕方なく裏の電源コードを抜いて再起動。立ち上がりません。二度ほど試しましたが同様。結局最上位機種でも不良品があるSONYでした。ついでにTVの展示の場所にルームリンク(?)のデモ用においてあったVAIO HS。これもフリーズしていました。マウスを動かしても液晶に画像がでず、強制電源断。なんとか再立ち上げできましたが。極めつけがWACOM Cintiqの展示に使われていたVAIOノートF。棚の下に隠れていましたが、見事に液晶ヒンジ部が破損。首が液晶のハーネスだけで繋がっているだけです。Mobile PentiumIII 450MHzモデルでした・・・。今日一日でもうVAIOが欲しくなくなります。なんて言う不良率だ(!)
September 23, 2003
コメント(2)
今日届きました。台風の中配達員さんご苦労様です(ぉとりあえず開封して眺めていました。それと、SocketA版Athlon/Duronが出た頃の雑誌を読み返していました。コアかけが怖いとか、グリスがたっぷり必要だとか。友人が丁度帰りに遊びに来ていたので放置していましたが、18時を過ぎて友人が帰ったので早速作業開始。Aptivaケースを開けてソケットにAthlonを差し、レバーを倒すのみ。ここで一番目の懸念事項が・・・。持ち合わせが丁度シルバーグリスで、これがキャパシタ(だったっけ?)に付着してショートしないかどうか心配で心配でならなかったのですが、ぐぐってみるとAthlon ThunderBirdでシルバーグリスを使っている方が居たので真似をして付けてみました。(実はぐぐる前にグリスを塗って仮にCPUクーラーを取り付けてみたのですが、コアからあふれてCPUの表面が汚れまくってしまい拭き取りに苦労しました。)第二の懸念事項が「CPUクーラーの取り付け」。「じょりっ」と行くとコアかけしてCPUお釈迦とか怖かったのですが何とか取り付け成功。ちなみに使ったCPUクーラーはAopenのCheCheブランドのやつで、友人からもらったやつです。Duronで使っていたのですが最悪な冷却性能だとか言ってました。大丈夫かなぁ?なんとか付け終え、意を決してケーブル類を接続後電源ON!結果、煙も出ずにIBMロゴを拝むことが出来ました。あとはすいすいWindows2000 ProfessionalをCDブートでインストール。インストール後にLANカードのドライバを入れ、ネットに接続後VIAの4in1ドライバ、S3 ProSavageビデオドライバ、VIA AC97サウンドコーデック用ドライバ、VIA チップセット内蔵LAN用ドライバをセットアップ。Windows2000 ProfessionalもSP4にアップデートし、IEも6SP1に。一通りセットアップしましたが疲れました。明日も続きがあると思われます。ちょっと使ってみましたが、かなり快適に動作しています。やはりPentiumIIIの対抗商品だっただけあってCeleronの動きとはひと味もふた味も違います。750MHzもあるのでウインドウの開閉もさくさく、ネットもかなり高速です。3GB HDDがちょっと異音を発していて怖いので早急に交換予定。追伸:家人2のFMV-6300DX2cなのですが、この際なのでオンボードのサウンドチップを引っぱがそうと思っています。こうすれば幽霊PCIデバイスも消えますし、PCIスロットのサウンドカードも使えるようになると思うので。とりあえずこの案に反対の方は理由と一緒に掲示板で書き込みいただけるとうれしいです。
September 22, 2003
コメント(0)
今日はまた一段と寒い日でした。朝から寒いし、昼間も昼寝をしようものなら風邪をひきそうになります。やはり台風の影響はすごいようです。(と言ってもそれに関係している秋雨前線の影響なんでしょうけど。)とりあえず寒いので昼寝するときにエアコンの暖房を使ったり、部屋でファンヒーターを使っていました。その甲斐も虚しく、どうやら鼻風邪になってしまったようです。このまま悪化しなければいいのですが・・・。休みを有効に使おうと思い立ったのがソフトのアップデート。案の定かなりの頻度で使用しているDivX Codecが5.1にアップデートされていました。早速アップデートしてみましたが、かなり使い勝手が悪いです。1.ダウンロードがしづらいAdware版やShareware版をDLさせたいのは見え見えで、Free DivX Codecは左下に小さくリンクがあります。ユーザーも探すの大変でしょうねぇ。同じように、RealNetworksのRealOne PlayerもFree版を探すのに多少苦労しますが、DivXほどではなかったようで。友人もFree DivX Codecが無くなったのと勘違いして私に持ってたらちょうだいと言ってきたほど(ぉ2.設定がしづらい設定画面が全面的に変更になっていて、Codecのプロパティもパフォーマンスの可変化に伴う設定が入ったと同時にクオリティ設定が何処かに失踪。3.処理が遅い!某所ニュースリリースでは「高速化」がされていると書かれていましたが、Celeron 650MHzのLaVie Cで今までコマ落ちしなかった映像までコマ落ちします。Celeron 400MHzのDESKPOWERでは今まで辛うじて鑑賞に堪える映像だったのがコマ落ち勃発で見るに耐えません。前述の通り設定が変更になっていて、とりあえずパフォーマンス可変設定を無効にしたり、いろいろ最小設定にしてみましたが変わらず。また、今まで弄ったことの無かったFilm Effectの設定も最小にしたところ少々速く描画されるようになりましたが画質がかなり下がりました。結論:使えねー。アンインスト後5.0.5にダウングレード決定動作環境はPentiumII 450MHz以上となっていましたが明らかにPentium4/AthlonXP以上向けのバージョンのような気がします。と言うわけで最新のソフトウェアが必ずしもいいとは限らない一例でした。DivX 5.0.5 Codecは永久保存することにします。追伸:先ほどDESKPOWERの方のDivX 5.1をアンインストールしてDivX 5.0.5にダウングレードしましたが、標準でFilm Effectは使用しない設定になっていたことが判明。とりあえずLaVie CはそのままだったのでFilm Effectを使用しない設定にして再度テストしてみました。結果、コマ落ちは5.0.5同様見られませんでした。結論2:バージョン上がったからってデフォルト設定は変更するなそれとQuality Settingsは必須。LaVie CはDivX 5.1でしばらくテスト使用してみることにします。
September 21, 2003
コメント(0)
NECの最新802.11a/b/g対応ワイヤレスルーター、AtermWR7600Hです。金欠なんで買えませんでした。じゃあなぜタイトルが「入手!」になっているかと?それは、「AtermBR1500HにAtermWR7600H用最新ファームウェア書き込み成功!」だったりするから(ぉとりあえず情報はネットでたまたま見つけたもの。標準のBR1500H最新ファームウェアではマルチセッションはルーターで一セッション張り、そこにPPPoEブリッジ機能でPPPoEクライアントを用いて他の接続先へ接続すると言うもの。当然PC側ではPPPoEクライアント接続が優先になるので、結局一台のPCで複数接続先へ同時接続は不可能となり、切り替える手間がかなり面倒でした。しかし、今回の方法でWR7600Hのファームウェアを書き込むとルーター側で最大5セッション接続を張ることが出来るのでPC側負担は一切なし。また、フレッツスクエアが目的ならフレッツスクエア用のセッションを張り、fletsドメインへのパケットをフレッツスクエアのセッションへ流れるように設定すれば楽勝に一台のPCで同時接続が可能です。なんでBR1500H用正式ファームウェアとして出さないの?と言った感じの出来です。しかもWR7600Hファームのはずなのにちゃんとトップには「BR1500H クイック設定Web」と表示されますし、無線関係の余計な設定も表示されません。スループットも全然変わらないので今回はかなりお得でした。今日は早めに日記を書きましたが、もう少し追記するかもです。
September 20, 2003
コメント(0)
今日は午後から異様な湿度でかなり蒸し暑かったです。しかもレポート提出が遅れて帰り歩きだし・・・。疲れまくったので寝室でエアコンつけて爆睡・・・のはずがなぜか19時に起きてしまったり。17時に寝たので2時間程度でしょうか。そして今は全然眠くないし。最近Windowsばかりで暇な生活なので、そろそろ他のOSも使ってみようかと思い立ったのがUNIX系OS。以前も何度かチャレンジしたのですが、貧弱なハードウェアで使おうと思ったのが間違いでした。何度も失敗し、KDEが起動できてもぜんぜん遅くて使い物にならないとか。また他のOSもある程度勉強しておいた方が良いかなぁと思い立ったわけで。と言うわけでハードウェアも使い回しでなく新規購入を考えています。ターゲットは値下がりが激しいMMX Pentium233MHz搭載のNEC VersaPro NX VA23C。家人と同じになってしまいますが、安さだとこれが一番。MMC-1なのでCPUを適宜PentiumII 300MHzあたりに換装しておけば結構快適に使えそうな。また、グラフィックがNeomagic MagicGraph128XD、サウンドがESS Maestro2、オンボードLANがIntel 21143、PCカードコントローラがTI社製とかなり枯れたハードウェア。同じようなハードウェア構成のThinkPad 600でもSolarisのインストール例があったのでそれを参考にしました。SolarisはSun Microsystemsの開発したUNIX系OSであり、教育関係で使うのはライセンス料が無料らしいです。しかし、肝心のメディアが高い・・・。日本のSunから購入しても5000円以上しますし、米SunからDLしようとしても約2000円。高校生にはかなりネックです。某個人売買サイトでたまにメディアキットが出ているのでそれを購入しようかと。若しくは誰かにコピーさせて貰うとか。ライセンスは別のはずなのでOKだと思うのですが。とりあえずSolarisメディア高すぎ。雑誌収録して欲しい物です。一つのOSだけだとつまらないのでRedHat LinuxとのDualブートを構築しようかと考えています。もちろんデスクトップ環境も考えて。KDEがなんとなくかっこいい気がするのですが・・・。最終的な構成としては、PC:NEC VersaPro NX VA23C/WSCPU:Mobile PentiumII 300MHzMEM:128MBHDD:10GBCD-ROM:24xLAN:Intel 21143 Onboard&ORINOCO Wireless LAN 11MbpsOS:Sun Solaris9 x86&RedHat Linux8と考えていますけど・・・。この通り上手く行くかが問題ですね。ついでに先日書いたThinkPad 600はサブマシン級になるのでコンボを搭載してWindows2000 Professionalになりそうです。出来れば54Mbps Wireless LANも付けたいところだけど我慢。
September 19, 2003
コメント(0)
体が持たん(ぉ連日のプールの授業云々で疲れはピークだし、レポートも書かなければならないしでもうだめぽ。116の受付が午後4時までだったような気がしたので、授業の休み時間にIP電話機器のレンタルをNTT東日本に申し込み。時間が無く生返事ばかりしていたらなぜかルータータイプのものがレンタルされることになり焦りました。NTT東日本のWebCaster V100。スループット30Mbpsで現在使っている98MbpsなAterm BR1500Hよりも劣りまくり。とりあえずこのままだと危ないので放課後に校門を出た瞬間116へ再連絡。いろいろまごついたものの、ルーターを使用している旨を伝えて無事にVoIPアダプタに変更して貰いました。スリムっぽいような。動作確認されたルーター一覧にBR1500Hがあったので安心です。@niftyフォンは月額料ただだし、初期費用もかからなかったのでお得でした。IP電話な話は置いておいて、テレビ台が到着したので組み立てを行いました。組み立ててみて一言。「電動ドライバーは必須!!!!!」手首がかなり疲れます。ネジ長すぎです。まぁ組み立て終えてFACEとビデオデッキを並べるとさまになりましたが。と言うわけで(?)世にも奇妙な物語も見終わったし寝ることにします。
September 18, 2003
コメント(0)
今日は授業でプールがあったり。疲れますた(ぉ家に帰ってからちょいと微妙な値段で購入したLogicoolのACCESS Keyboard iK-27を開封して試してみました。LogicoolのiTouch機能付きとしては破格のやつです。面倒だったのでThinkPad 390に繋いで動作確認。標準の106キーは使えました。また、特殊ボタンもメールとホームと音量調節キーはドライバを入れなくても使えました。唯一欠点と言えばUSB未対応なのとキータッチが今使っているLogicool iTouchキーボードより浅いことです。いろいろ書きましたが、ショップで800円ノーブランドキーボードを買うより、追金してこのキーボードを購入した方がいいかと。マウスも用意しないと・・・。ちなみにThinkPad 600はLogicoolではないMS製のIntelliMouse Opticalでも繋ぐ予定です。安いみたいだし・・・。とりあえず最近は日記ネタが欠乏気味ですが、何とか用意できています。長続きしそうもないような気が。
September 17, 2003
コメント(0)
やっちまいました。いつもの癖で・・・。興味があるジャンク品を見つけると必ずと言っていいほど買ってしまう癖が裏目に出てしまいました。阪神タイガース優勝の影響が・・・無きにしも非ずかも(爆)とりあえず購入してしまったもの(ぉキータッチなどかなり評判のIBM ThinkPad 600。ジャンクで12K。メモリを刺して起動させるとエラーが出て、HDDが欠品だというもの。CMOSバッテリ切れとHDDが無いことによるエラーだと思ったりしてます。写真を見る限りHDDステーごと無いようです。また、HDDドアも無いような。ステーは若松通商でで互換品を買うか、IBMから取り寄せられますが(千数百円)、HDDドアは異様に高いようで6000円くらいしやがります。とりあえず放置しましょう。ACも無いけど390と同じやつが使えそうなのでそのうち手に入れます。FDDが無いとBIOSアップデートできないんですよね・・・。これも必要かも。安易にCDブートできるからいいやと考えていましたが・・・。CDブートでWindows2000を入れる予定でした。一応最初の予定では、CPU:ノーマルPentiumIIメモリ:32MBオンボード+128MB=160MBHDD:20GBで行こうかと思っています。後々改造しそうですけど。と言うわけで金欠さらに加速。火の車になりかねません。とりあえずかなりゆっくりなペースで進めようと考えています。・・・この前買ったTrackPointキャップの予備はドコへ・・・。
September 16, 2003
コメント(0)
今日は連休最終日。短かったような。とりあえず先日手に入れたIBMの14.1インチ液晶ディスプレイ、9514-A04を弄ってみることにしました。電源投入から数十分は綺麗に映るのですが、途中で真ん中に白い横帯が出てしまうと言うもの。早速ばらします。ネジが多すぎです。前修理した富士通の15インチ液晶ディスプレイVL-15TX3Gの数倍ネジがあります。しかし規格が統一されているので組み立て時は楽です。まず疑った液晶パネルとコントローラを接続する部分の接触不良。暖まってくると症状が発生するためコネクタ裏から半田ゴテで少々暖めてやりました。それと半田を盛り直せるところの半田盛り直し。また、液晶ドライバLSI(全てIBM自社製!)が熱くなるらしく、内部のアルミケースにヒートシンクが取り付けられていました。熱伝導シールらしきものが付いていましたが、何となく頼りないので剥がしてシリコングリスを塗りたくりました。以前PowerLeapのPL-iP3/Tを購入したときに付属していた銀入りのものです。これ以外無かったので。はみ出してLSIの足同士がショートすると逝く可能性大なので慎重に何度も接触具合を確認しました。何とか組み上げて動作確認。やはり症状は直っていませんでした(泣)しかし、それからの検証で・帯の両サイドのフレーム部分を押すと数分直る・それでも直らなくなったらフレームの左上と右下を強めに押すと一時的に直るという結果になりました。接触不良なのかもしれませんが、抵抗やコンデンサ・トランジスタが原因かもしれないという考えまで・・・。一番簡単なのが、・液晶割れorバックライト切れの同型機種と二個一!かもしれません。でも今持っている液晶パネル自体に問題があるのだと全然意味がないのですが。これで疲れ果てましたが、もう一つ液晶ディスプレイネタ。数ヶ月前に偶然修理できてしまった富士通の液晶ディスプレイですが、画面がちらつくしスタートボタンの文字が微妙に揺れているのがかなり気になっていました。また、ジャンク入手時D-Sub15ピンケーブルのコネクタが若干さびていたのと、砂っぽいものが出てきたことからケーブルの交換と再メンテが必要かなぁと思っていました。しかし、今日あることを試したら、メンテナンスをしなくても良さそうなことが判明。と言うのも、「リフレッシュレートの変更」でちらつきがぴたっと収まってしまったからです。プラグアンドプレイモニタとしてXP上で認識されていたこの液晶ですが、60Hzしかリフレッシュレートを選べなくなっていました。しかし、横の「このモニタでは表示できないモードを隠す」のようなチェックボックスを外すと手動設定できる事が判明。早速リフレッシュレートの変更を行ってみたところ、75Hzでゆれがぴたっと収まったのでした。まぁ、根本的に液晶側に問題があったのだと思いますが、ひとまず楽に解決できてよかったです。そのうち(と言うより早めに)新しいRGBケーブルを購入して取り替えたいと思っています。そうそう、キーボードの腕が最近なまってきたようなのでおなじみSOURCENEXTの特打をやってみました。基礎のコースで一番簡単なものはトップにランク入りしましたがそれ以外はどうしても2位以下。日頃の精進が大切なようです。
September 15, 2003
コメント(2)
今日は休みです。まぁ昨日もなのですが(笑)とりあえず起きると、体中が痛い痛い。やはり29型テレビを家の二階から下の道路まで下ろすのはかなり体に負担をかけるようで。家の場合、一階の下にもう一階車庫の分の段があるので疲れまくりな訳です。だからといってずっと寝ているわけにもいかず起床。朝っぱらからエアコンの掃除や換気扇の掃除や階段の掃除などやってました。とりあえず一段落して休んでいると何とも涼しい風が。昨日テレビを29型から21型に変更したおかげで窓が開くようになった親の寝室も、つい数ヶ月前にパソコンデスクの配置換えをして窓が開放された自室も風が自然と吹き込んでくるようで。ついでなので階段の吹き抜けにある同方向の窓を開けるとまったく同じくらいに風が入ってきてかなり涼しかったです。秋らしい日でした。午後からPCをちょいと弄り始めてみたり。家人3のVersaProにRasPPPoEを仕組んでマルチセッションでガンダムSEEDでも見ようかと思ったら接続して数分でndisがエラーを吐いて接続が切れることが判明。Intersil PRISMな無線LANがいけないのか、はたまたLAN設定がおかしいのかと。面倒なので重たいフレッツ接続ツールV2.0でも入れて使おうかなぁと思ってます。家人2のFMV-6300DX2cは相変わらずサウンドが鳴らないまま。色々試してもKernel Audioなどが「ドライバが壊れています」でエラーになりますし。いろいろドライバのアンインストールも試しましたがだめでした。おとなしく6xxxDXへ移行しようかと思っています。家人1のBIBLO NEVIII23Xはバッテリの認識がおかしくなっていることが判明。状態表示LCDのバッテリ残量表示が上がったり下がったりで一向に充電されていない様子。しかもそれに併せてWindowsのバッテリメーターまで数値が上下。充電中のはずなのに。充電されているのかと思ってACを外すと起動できないし。これがメインボード側の故障なのか、はたまたバッテリ側の故障なのかは分からないのですが、せめてバッテリ側であって欲しいです。ジャンク化したPS2がただのPSとして使われて久しいのですが買い換えや修理はまだまだ先になりそうです。PS2が無いなりにN64やDCやGBAなどで遊んでいるっぽいので。
September 14, 2003
コメント(0)
今日は朝からいろいろしていました。何となく気が向いたので朝飯に自分で作ったスープを追加してみたり、部屋のデッキの配置を交換してみたり。その中でも一番苦労したのがジャンクなDVD-ROMドライブでした。先日何となくベゼル取りにはなるだろうと購入したジャンクなPioneer DVD-113と前に同DVD-114のベゼル用に購入したDVDしか読めないPioneer DVD-115です。まずは先日購入したDVD-113を試すことに。VALUESTARの空きベイに装着し、余っているプライマリマスターに接続。XPを起動するとデバイスを認識しますが、なぜか「PIONEER DVD ROM」で製品名が終わっています。また、ディスクを入れても回転しているようだけど読み込めず。I/Oエラー勃発。ROMが逝っているのかとDVD-113用ファームウェアを書き込んでも書き込み前に「対象機種ではない」と跳ねられてしまいます。RPC-1用改造ファームウェアや他社OEM用の改造書き込みソフトを使ってみましたが変わらず。あきらめてレンズをDVD-115に移植するかとばらすとなんと!DVD-115とピックアップ周りは形状が似ているものの、ハーネスのコネクタのピン数が違います!!そして、ローディング云々に使われそうなモーターの数も異なっています。面倒だからと一緒にばらしていたDVD-115は元に戻しました。そしてVALUESTARで動作チェックを・・・とやってみるとやはり「PIONEER DVD ROM」と認識されて読み込みできない様子。これでやっとIDEインターフェース側の異常だと判断できました。とりあえずセカンダリに繋ぎ直すと一発認識。DVDレンズクリーナーを試すもCDは読めず。だれかレーザー出力調整して!と言うような感じかも。ついでなので最新ファームにアップデート。すんなりいきました。もしやと思ってDVD-113も組み立て直すとちゃんと「PIONEER DVD-ROM DVD-113」と認識されました。そのままファームウェアを書き換えてもさっきの苦労が嘘のようにほんの数十秒で書き換え完了。しかし、CD-ROMなど入れても回らない様子。またもう少し研究が必要そうです。というわけで、なぜか書いてないけど昼間に近所を回っていた家電回収業の人に壊れた29型テレビを渡すために二階から道路までテレビを持ってかなり疲れ気味の管理人でした。
September 13, 2003
コメント(0)
今日も暑い日。やっと一週間が終わりました。帰りに電波が弱いような”気が”するP504iSを診て貰おうとドコモショップへ。結果全然問題なかったようで。データが消えたりすると面倒なのでそのまま持ち帰ってきました。やはり電波が弱いのは仕方のないことなんでしょうね。もしかすると高速パケット通信(28.8Kbps)を搭載した事による弊害なんでしょうかね。まぁここいらで切り上げて帰宅。昨日届いた商品はもう一つありました。ジャンクビデオデッキです。三菱のHV-MY30です。(上の写真は参考です。デジカメで撮影できないほど部屋が散らかっているためすみません。)故障内容はテープが絡んだときにルーフを開けてテープを外したがそれから音声が出ないと言うものです。ふらっと購入してしまいました。とりあえず症状を確認。デッキに適当なテープを入れて再生させますが、LR表示が出ていません。また、デジタルオートトラッキングが作動しているときのD表示が点灯に変わるまでかなり時間がかかります。もしやと思い、クリーニングテープ(湿式と乾式)を試してみたところ、テープ再生時のLR表示も復活し、デジタルオートトラッキングも素早く動くようになってしまいました。それから何本かテープを入れてみましたが問題ないようです。500倍速巻き戻しはさすがに怖いのですが・・・。というわけでただいまダビングに酷使中。送り側がこの三菱HV-MY30で受け側が同三菱HV-S780です。リモコンがコードを変えるだけで使い回せるのはありがたいです。それと、説明書も付いてきたので助かりました。とりあえずこのデッキにはS-VHS用ビデオヘッドが使われているという話らしいので試しにNV-SB600Wで録画したテープを再生してみました。その結果、なぜかメダカノイズ消滅。この結果から、「デッキとテープに相性があり、Victor製S-VHSテープは家のNV-SB600Wで三倍録画する場合には相性が悪い」という仮説を立てました。ううむ。なので、以前使っていたTDKのXPの録画済みをHV-MY30で再生し、HV-S780で録画するという暴挙に出ています。そして、以前NV-SB600Wで録画したVictorのS-VHSテープをHV-MY30で録画して余ったTDKのXPへ移すというなんとも面倒な作業をやっているわけです。疲れまくりです。それにしてもかなりお買い得なビデオデッキでした。ありがたや。タイトルのもう一つ、FMV-6300DX2cにAopenのCobra AW850を搭載してみた話なのですがXPをクリーンインストールしてC-Mediaから落としたドライバをインストールしても音が鳴った瞬間にフリーズします。やはり正常に動いているように見えるPCIステアリングが異常なのでしょうか。やはりIRQが割り振られない幽霊Crystal SoundFusionが祟っているのでしょうか?面倒なのでこのFMV-6300DX2cはケースだけ利用することにして中身はFMV-6266DX辺りに入れ替えることにします。FM90AAなのでM63用BIOSが普通に使えます。ジャンパでISA接続オンボードCrystalを殺してこのAopen Cobra AW850を搭載する予定。かなり遠回りな結果になってしまいました。FMVも440BXチップセット機でさえこうじゃじゃ馬なので「隣の芝は青い」がもろに当てはまる結果になってしまいました。
September 12, 2003
コメント(0)
今日は先日犯行を仄めかしていた(!)家人のFMVデスクトップ、FMV-6300DX2cへのサウンドカード増設を行ってみました。物は先日の記載通りAopenのC-Media CMI8738搭載サウンドカード、Cobra AW850です。6CH対応らしく、スピーカー出力が三系統もある品物。早速取り付け、WindowsXPを始動。(IBMみたいな書き方?)普通にXPが起動し、「新しいハードウェアが見つかりました」と表示され、「マルチメディアオーディオコントローラ」がインストール開始したようです。しかし、一向に表示が変わらないので手動でデバマネからドライバをインストール。タスクトレイに音量のアイコンがでないので、コントロールパネルから有効にしようとサウンドとオーディオのプロパティに入った瞬間フリーズ。マウスもキーボードも効かなくなり強制電源断。電源を入れ直すも、起動途中でフリーズ。いろいろセーフモードで起動したり云々しましたがドライバを消すと問題ないものの、ドライバを入れたとたんに不安定になると言う症状に見舞われました。結局TVチューナーカードと相性が悪いのかと抜いて再実験。何とか起動時の音が鳴るようにはなりましたが、やはりすこし作業すると固まります。次はTVチューナーカードとサウンドカードをそれぞれ反対の場所に移転して実験。結果は同等でした。また、CPUの熱暴走も考え、ファン付きのPII-266MHzに換装してみましたが結局症状は変わらず。全然進歩がありません。こんなにサウンドカードの増設に苦労するものだとは思いもしませんでした。オンボードCrystal SoundFusionの祟りなんでしょうか・・・。とりあえず最終手段の一歩手前と言うことで、XPのin-place Upgradeを実験中。たかがCMI8738如きでここまで労力を消費するのは私ぐらいのような。
September 11, 2003
コメント(0)
今日は暑かったです。調理実習とプールの授業があった程度。調理実習は久々だったのですが結構上手くいきました。まぁあそこまで凝った料理は家でも作りませんけどね。とりあえず帰宅も至って普通でした。帰りに友人にGAMEBOY COLORを貸した程度かな。それからクーラーが効いた部屋でうとうとと・・・。最近は部屋に行ってLaVie CやDESKPOWERを触る気がせず、もっぱら隣のクーラーの効いた部屋でThinkPadを使っている毎日です。日記ネタがどんどんなくなっている毎日です。本当に。これで終わるのも暇なので少々書き足し。ThinkPadとLaVie NXの内蔵CD-ROMドライブが逝って久しいのですが、そろそろLaVie NXの不安定なWindowsMeをWindows2000に入れ替えたいし、ThinkPadでもCDからインストールしたいソフトやOSのデュアルブート環境を構築したいと思っているのでCD-ROMドライブが必要かなと。なのでLaVie NXには今付いているTEAC CD-220Eと同じものを購入して交換する予定。この年代のものはCSEL/MASTER/SLAVE切り替えが本体のスイッチで切り替えられるそうで、しかも同一種類ならベゼルも共有可能ですし。ThinkPadには適当なCD-R/RWドライブを搭載する予定。ThinkPadのCDベゼルは特殊な形なのでかなり無愛想になりそうな予感。しかも標準搭載が今時見かけない三洋製。CRD-S372Bなどという得体の知れないドライブなのでベゼル移植も無理でしょう。しかし、我がThinkPad390はCD-ROMドライブがFDDとともに着脱できるので換装は簡単かも。というわけで、今日はノート機方面の環境整備を考えてみました。そろそろAthlon 750MHz Thunderbirdが届くのでしょうかねぇ。
September 10, 2003
コメント(0)
今日は何となく短縮授業で数時間早く帰宅。最近行っている敷地内公共下水道敷設工事もなんとか終わったようで、家の周りも綺麗に片づいていました。下水の枡や浄化槽・それ以外の今までの下水設備も新しい下水道設備に一新し、かなり片づいているようです。風呂場でシャワーを浴びても快適に排水されるようになりましたし。とりあえず良かったようです。今日も何となく暇で、昨日使用したIBMの14.1インチ液晶ディスプレイを使って昔実用に耐えないと使用をあきらめたマルチディスプレイを試すことに。結果は以前の通り、セカンダリ側で動画再生するとカクカクする上にプライマリ側でもちらつくという常用できない結果に。しかし、今回は趣向を変えてプライマリ側で動画を再生し、セカンダリでメールやWebをしてみました。すると、かなり実用に耐える速度で描画されることが判明。ほとんどCPUの処理速度と言っていいほどの動画再生時の遅延でした。やはりジャンクな液晶で、使っていて十分くらいで真ん中に太い白帯が入りました。(幅4cmくらい?)白くなっている部分には薄いですが描画はされているようです。とりあえず半田付けで対処予定。コンデンサ類やトランジスタ類の交換だと厄介ですけど。話は飛びまくりですが、家人2のパソコンのオンボードサウンド行方不明事件ですが、結局別にサウンドカードを購入することで対処。彼はパッケージの絵柄に気に入ったのか、AopenのCobra AW850を購入と相成りました。廉価サウンドチップとしてはかなり有名なCMedia製CMI8738搭載PCIサウンドカードです。アナログ5.1CH対応で、DLS WavetableなMIDI搭載です。まぁ、しょっぱいMIDIは置いておいて、結局はS-YXG50ソフトウェアXG音源を使うんですけどね。祖父地図のインターネット販売で購入しました。数日後に到着するようです。まぁ、ポイントカードをなぜか持っていたりしますのでね。このままだと間違いなくPCIスロット不足に陥るので早めにFMV-DESKPOWER SVI/SVIIケースへ載せ替える必要がありそうです。
September 9, 2003
コメント(0)
月曜日。また一週間が始まりました。帰りに電器店に寄って不調な石油ファンヒータを買い換えるための下見やdynabook EXを使ってみたりしていました。帰宅してから、やっとこさDESKPOWERのHDD接続ケーブルを交換する気になったので作業を初めました。普通に本体をばらして購入したATA/133対応HDDケーブルに交換。所要時間2分。今までのATA/66ケーブルが滅茶苦茶な取り回しだったので合理的かつ綺麗に配線。フラットな面があまり無くならないようにしました。ケースをしめる前に動作確認をとモニタを接続。面倒だったので先日購入したIBM 14.1インチTFT液晶を。17インチは重いので。起動させると、普通にMaxtorのほうのHDDからシーク音が聞こえましたし、Windows2000でも認識。何度か再起動してもHDD行方不明事件は発生しなくなったので原因はケーブルの断線と考えて良さそうです。しかし、HDDはATA/66動作をしないので結局BIOSを上げた事によるライザーカードとの相性のようで。今度スリムタワーケースに移行して何かに使う予定。(サーバーがいいところかも。)FMV-DESKPOWER CIX355あたりが激安でよさげ。何はともあれ、直って現役復帰できてよかったです。
September 8, 2003
コメント(0)
最近よく考えているメーカー機ケースでの自作。そこにたまにあるのが、スロットカバーが6本しかないATXケース。IBMのAptiva 2140や富士通FMV Tシリーズ、東芝のBREZZA・EQUIUMシリーズなどが該当します。(コアな話だと、MATE Server NX MA30Eなんてのも同じような話。)これらのケースで最新のマザーを使うと、大半がAGPスロットと裏のスロットカバーがない部分が当たってしまいます。(と言うわけで穴を開けない限りAGP使用不可。痛い!)そこで必要になるのが計6本しか拡張スロット類がないマザー。最近はめっきり見なくなっていたので、久々にそれを調べていたところ、ASUSの現行マザーにたくさんあることが判明。AthlonXPをFSB400で動かせるnForceなA7N8X-Xも、Pentium4対応なi875PのP4C800もそのようで。とりあえずスロット6本物のケースを手に入れたらじっくり考えたいと思います。作ってみたいのは、漆黒のAptiva 2140ケースにASUSのA7N8X-X、中古でRADEON 8500LEあたりを。AthlonXP 2500+なんかよさげ。黒い液晶ディスプレイとかキーボード・マウスを揃えてシックに行きたいと思ってみたり。午後からスパム対策しまくりで疲れまくりの管理人でした。ビデオデッキの昨日の不具合ですが、ノイズに目をつぶればVHSとは一線を画する画質です。シャープでDVDと同じような画質のような気がしました。
September 7, 2003
コメント(0)
今日はやっと週末。休みなので寝てるかと思いましたが、休日出勤の用事があり渋々起床。学校で用事を済ませ、帰りに電器店でUltraATA/133対応フラットケーブルを購入して帰宅。駅で中学校の時の友人にあって数十分話した以外はごく普通でした。家に帰ってからPanasonic NV-SB600WでS-VHS録画を試したS-VHSテープを部屋の三菱HV-S780で再生。その画質に唖然としました。メダカノイズ入りまくりです。右の人の首の辺りにノイズが入っているのはおわかりでしょうか?もう少し分かりやすいものはこれ。(あまり変わらない?)右に見える腕の関節あたりにノイズが・・・。先日NV-SB600WでVHSテープにVHS録画した際は正常だったのでやはりS-VHSヘッドでも痛んでいるのでしょうか?または回路の不具合とか。和室のNV-SB66WでもVHSテープに三倍録画をしてみたところ同じようにメダカノイズが入っていたことがありましたが。面倒なので録画機を入れ替える予定です。もちろん、3次元DNR・3次元Y/C分離・TBC搭載のデッキで。日立の7B-SV500か7B-BS700あたりがジャンクで手頃のようです。なので入手して入れ替え予定。S-VHS ETも付いているし。修理方法は以前修理した7B-BF300と同様。やはり録画する際は一度デッキとテープの相性等確認した方が良さそうです。さて、後でFMV-DESKPOWER SVI265のフラットケーブル交換でもしましょうかね。
September 6, 2003
コメント(0)
やっと今週の授業が終了しました。長かったような短かったような。とりあえず家に帰って部屋でPCを立ち上げました。FMV-DESKPOWER SVI265がスレーブのMaxtor DiamondMax 90644D3を認識しなくなっているけど気にしない気にしない(爆)マスターのSeagate BarracudaATAもATA/66で動かないのでケーブル不良の線濃厚。Maxtorもディスク回転はちゃんとしているようですので。BIOSやOSで認識されないだけ。こういうのは放っておいて、先日Windowsセットアップで四苦八苦しまくってBIOSを更新したらオンボードサウンドが逝ったFMV-6300DX2cに再度戦いを挑んでみました。今回使う小道具は部屋の本棚に入っていたWindows XP HomeEdition。とりあえずOSをNT系にすれば少しは楽になるかなぁと思い立ったが吉日で早速やってみた次第です。インストールは単純明快で、適当に進めればOK。認証はしないことに。そりゃ他のPCで使ってますからね。動くかなぁ程度の考えです。Celeron 300AMHz・128MB RAM・4.3GB HDDで一時間程度でセットアップが完了しました。もちろん音は鳴りませんけど。デバイスマネージャを見ると感動!インストールをまだしていないTVチューナーカードと、逝ったCrystal SoundFusionにしか!マークは付いていません。TVチューナーもCDを入れるだけでドライバ更新完了。Crystalは明示的に使用しない設定にしてかなり快適です。オンボードのATI RAGE PRO TURBOもLunaで結構さくさく動いています。(1024x768 32bit表示で)また、Meでは全然使えなかったスタンバイ・休止もスタンバイはドライバの問題か出来ませんが休止がしっかりと出来るようになり感動です。IEなどもそれなりに軽く動いていますし。と言うわけでこのPCの余生はNTカーネル系OSで行くことになりました。いつもならWindows2000ですませるのですが、やはりXPの方が良さそうです。なぜなら、・Windows2000はネットワーク設定で死ぬ(共有アクセス権とかわざわざ明示的に設定しないといけない)・ログオン関係が古くさくて分かりづらい(XPは「ようこそ」画面で視覚的に簡単)・家人2の通う学校のPCはすでにXP Proだ(やはり学校と同じ環境に慣れた方が楽?)・家人2が「XPほし~い」とほざく(居間のPCをばりばりLunaなXPで使った影響?)結構OSの選定は大変ですが、XP Homeで使うことになりそうです。あとはソフトを買うのみかと。明日はまた学校で半日程度P4+WindowsXP Proで疲れそうです。遊ぶ要素が無くてつまらなさすぎです。
September 5, 2003
コメント(0)
今日も普通でした。帰ってきてからVALUESTAR NX VM35/4ZDを立ち上げてメールチェックをしようとしていましたが、最近立ち上がりが遅いようです。ずっとHDDのアクセスランプが点滅したままですし。とりあえずメールチェックを済ませた後にIEを起動。これもなぜかHDDを読み込みまくりで遅いです。そして致命的なのがWebブラウジング中の異常表示。ページをスクロールマウスのホイールでスクロールしているといきなり画面が消えて点き、マウスポインタが滅茶苦茶な表示になります。また、表示されている文章の文字も崩れます。ヘタに長いページでずっとスクロールしていると何度も画面が点滅してポインタが異常になり、目障りで最悪です。しかも時にはIEのスクロールもそこから動かなくなり、操作性が滅茶苦茶にだめです。原因は、・OSを上書きインストールしたためのファイル不整合(特にDirectX9.0関係が怪しいような・・・。)・爺256が逝きかけている(これは一番考えたくないシナリオだったり・・・。)・マザーが逝きかけている(まぁジャンク付属品あり9800円で購入した機体ですし・・・。)HDDの容量不足でCのファイルをDに移すことも出来ず、そのためクリーンインストールすら出来ません。仮にHDDを新しい物に換装してOSをクリーンインストールしたところで直るかどうかも怪しいですし・・・。もうこうなったら!!!!!と思い立ったのがFMV-PRO作成。Pentium4 3.2GHz2GB RAM250GB HDDRADEON 9800 PRODVD±RWWindowsXP Proで組もうかなんて勢いで出てきましたが、無論無理です。結局前回までのスペックで止まりそうな気がしますが、学生のため金欠なのと年賀状を作成する12月末までに直さなければならないと言う期限の短さから、Celeron 2.4GHz256MB RAM120GB HDDi865G OnboardDVD-ROM/CD-R/RWWindowsXP Homeというような構成になってしまうかもしれません。特にCeleronと言う項目が異常に気に入らないのですが、中古でも1万円でP4が買えないので渋々・・・という感じです。ちなみにAthlonXPマシンは部屋に一度導入してみてからのお楽しみ。その前にAthlonなAptiva E Seriesを組み立て終えないと・・・。マシンが多いので一台にばかり金をつぎ込むことが出来ないのは痛いところです。自分でも増やしすぎたような気がしてなりません。まぁ、これだけあれば家庭内LANがLANらしく機能してくれるんだと思いますけどね。というわけで、完全にメインPCがLaVie Cになってしまった管理人でした。
September 4, 2003
コメント(0)
昨日まで家人2のFMVでかなり面倒でしたが、サウンドカードも無く、オンボードも使えないのでとりあえず保留になりました。というわけでAptiva制作のパーツ調達にでもと学校帰りに近所の電器店へ。頂いたAptivaマザーはオンボードLANが不調なようなのでLANカード購入。LowProfilePCIでWOLとWindows2000に対応しかつ安いものを探しました。すると、PlanexのFNW-9803-Tしか選択肢がありませんでした。ADMtekのAN983B(DECの21140互換?)チップ搭載のもので、VLANだのQoS対応だの書いてありました。まぁ、家の有線LANはほとんどがIntel製で、そんなの当たり前なのですが。また、その機能はあっても使ったことが無く、宝の持ち腐れっぽいです。とりあえず1100円+TAXで購入。安いカードは軒並み蟹さんチップセットだったのでいい感じです。以前、同社のFNW-9802-TというLANカードを使っていましたがチップは変わらないようです。また、家に帰ってから早速取り付けてみましたが、マザー上にWOLコネクタが見あたりません。PCI2.2対応だとWOLケーブルを刺さなくてもWOL出来るという話を聞いたことがあるのでそれに賭けることにします。
September 3, 2003
コメント(0)
今日もFMV-6300DX2cのセットアップに追われる羽目に。ACPIが動かない440BXマシンなんて・・・と大胆な行動に踏み切りましたが、それがやはり失敗してしまいました。とりあえず今日もPCの調子が悪く、省電力系がさらさらだめなのでBIOSがACPIに対応していないのではないかと思い、BIOSをアップデートすることに。もちろん、公式サイトにBIOSアップデートはなく、頼みの綱のFujitsu Siemensにはありました。しかし、オンボードサウンドがISAのもの、あるいはオンボードサウンドなし用のBIOSでした。探してみると、FMV-6266DXなどのM63(FM90AA)用BIOSのようでした。そこで私は何とかなると考えてやってしまったBIOSアップデート!結果、書き込みは成功し、ちゃんと起動したのですが、兼ねてから不安だった某デバイスが使用できませんでした。「音ならないじゃん!!!」やはり敷居はそんなに低くないようです。オンボードサウンドがPCIだったためか、BIOSで認識されず、IRQも割り振られないので音が鳴らなくなりました。PCIバスのIRQエラーも復活し、かなり面倒な事態に。オンボードサウンドを切り離そうとマザーを見てもジャンパがない様子。その状態でジャンク箱から漁ってきたYMF724を刺しても音が鳴らず。認識もされません。思い切ってまたクリーンインストールを行ってもだめでした。YMF724が逝っているのかもしれません。PCI IRQステアリングのエラーが出るのは間違いなくBIOSに無視されているOnboard Crystal SoundFusionのせいなので、1.はんだごてでCS4614を引っぺがす。(こうすればIRQステアリングも元通り?しかし、サウンドカードが必要。)2.おとなしくFM90PA用BIOSに戻す。(でも元のBIOSが残っていないんですよね。どうすれば・・・。)という二択になってしまいました。後悔しまくりです。これがFMV-6266DXなどのFM90AAマザーならBIOSアップデートも問題なくすんで、ACPIも問題なく使えたっぽいのですが残念です。これからどうするべきかとIRQエラーが出て音が鳴らないFMV-6300DX2cの前で悩む管理人でした。
September 2, 2003
コメント(0)
今日は学校から帰ってきてすぐにFMV-6300DX2cの環境構築の続きを行いました。ひどいことに、TV鑑賞アプリケーションを起動するとともにブルースクリーンで落ちるようになりました。それが何度やっても落ちるので、嫌気が差してまたOSをクリーンインストール。今回はドライブがすでに売却済みだったため、媒体を変える手に出ました。他のCD-Rにコピーしてそこからセットアップを実行。何とか上手くいきました。setup実行時、ちょっとした構文を加えたのですがそれが後で仇となるとは・・・・。その構文はsetup /is /im /nm /ie /p jです。最後の1文字が余計だったのです。ACPIなんてかまさなければよかったと後悔。何とかACPIモードでセットアップできましたが、その後ひどいことに。省電力重視でACPIにしたのにスタンバイや休止状態が出来なくなっているではありませんか!APMでインストールした昨日では休止もスタンバイもメニューにあったのに今回はありません。nohiber.txtを参照するとPCI IRQステアリングがおかしいそうで。PCIバスのプロパティを見ると、「IRQステアリングが使用不可になりました」と一文。ACPI BIOSから云々のチェックボックスを外して再起動すると、IRQステアリングは直っていましたが相変わらずスタンバイや休止状態は出来ないまま。いろいろ試行錯誤しているうちにまたしてもてっぺんを回ってしまいました。予想以上に気むずかしいPCのようです。素直にK28搭載のSVIII・SIXにしておけば良かったかなぁ。
September 1, 2003
コメント(0)
全30件 (30件中 1-30件目)
1